TRANSFER
KNOB
H 9 6 5 8 6 3
3
INSTALL VALVE BODIES
INSTALL HANDLES
2
2a
HOSE ASSEMBLY
HAND SHOWER ASSEMBLY
Note: Back flow prevention and 2.5 GPM flow
restrictions are included with all Roman tub
sets with hand shower
Insert FIBER WASHERS
(1)
into COUPLING NUTS
(2)
of SUPPLY
HOSES
(3)
and tighten.
1-1/2'' MAX.
"O" RING
Thread LOCKNUT
(8)
to bottom of VALVE BODY
(2)
. Make sure
FIBER WASHER
(9)
and RUBBER WASHER
(10)
are installed.
Insert VALVE BODY
(2)
through mounting hole from underside
of tub deck or mounting surface.
Note: VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting surface thickness is 1-2/4".
HANDLE ASSEMBLIES
(1, 1A)
are installed on VALVE BODIES
(2)
and must be removed to install VALVE BODIES
(2)
from under tub
deck or mounting surface.
To remove HANDLE ASSEMBLY
(1)
, unthread HANDLE BASE
(3)
with
LEVER
(4)
from VALVE BODY
(2)
. Pull HANDLE ASSEMBLY
(1)
off
VALVE STEM
(5)
.
Unthread and remove MOUNTING RING
(6)
and SPACER
(7)
.
From top install SPACER
(7)
onto VALVE BODY
(2)
. Thread
MOUNTING RING
(6)
on VALVE BODY
(2)
until seated tightly against
SPACER
(7)
. Set VALVE BODIES
(2)
so that their outlets are facing
toward SPOUT TEE
(11)
and then tighten LOCKNUT
(8)
using 35mm
or adjustable wrench.
Insert FIBER WASHERS
(12)
into COUPLING NUTS
(13)
of
SUPPLY HOSES
(14)
and tighten making water tight connection.
Important: Loop SUPPLY HOSES
(14)
as illustrated so they do not kink.
6
1
3
4
8
12
HOT
13
14
9
11
10
7
5
2
JADO
"O" RING
TUB DECK OR
MOUNTING SURFACE
Turn VALVE BODIES
(2)
to off position. Align HANDLES as shown or as desired
and install HANDLE ASSEMBLY
(1, 1A)
onto VALVE STEM
(5)
. Thread HANDLE
BASE
(3)
onto VALVE BODY
(2)
until seated tightly against mounting surface.
Drop SPRAY HOLDER
(4)
into the fourth hole of the tub
ledge or deck (12" max from SPOUT center) directed
towards tub center. Be sure O-RING
(5)
is properly
seated in ESCUTCHEON
(6)
. Install RUBBER
WASHER
(7)
, FIBER WASHER (8) and LOCKNUT
(9)
from underside of mounting ledge. Secure
SPRAY HOLDER
(4)
by tightening LOCKNUT
(9)
.
Add SEAL WASHER
(10)
and connect COUPLING
NUT
(11)
of BRAIDED HOSE
(12)
to outlet nipple.
Tighten firmly. Tighten SPRAY REST
(19)
.
Slip SHOWER HOSE
(13)
with COUPLING
NUT
(14)
through SPRAY HOLDER
(4)
and
ESCUTCHEON
(6)
.
Install SEAL
(15)
into COUPLING NUT
(14)
. Connect
COUPLING NUT (15) to HOSE NIPPLE (16) and tighten.
INSTALL second SEAL
(15)
and connect HAND
SHOWER
(17)
to SPRAY HOSE END
(18)
. Hand tighten.
14
2
2
1
1
11
12
13
3
3
10
15
8
BRAIDED
HOSE
16
15
5
6
4
OUTLET
NIPPLE
9
18
7
3
HOT
COLD
3/4" D.
19
17
