SMALL
END
LARGE
END
LARGE
END
VALVE
OUTLET
VALVE
OUTLET
PUTTY
1
2
3
H 9 6 5 12 5 F
5
6
INSTALL SUPPLY HOSES
INSTALL SPRAY BODY
INSTALL HANDLES
Connect small end of SUPPLY HOSES
(1)
TO "Y" ADAPTER
(2)
and larger end to each VALVE OUTLET.
Important: Loop SUPPLY HOSES
(1)
as illustrated
so they do not kink.
Connect one end of SPRAY HOSE
(7)
to HOSE ADAPTER
(8)
and the other end to shank of SPRAY BODY
(3)
. Tighten hose
connections to make a water tight seal.
7, 8
6
2
4
5
1
3
9
10
11
12
Hex wench, supplied
BIDET
MOUNTING
SURFACE
DIVERTER
For Cross handles:
Turn
VALVE to off position and align
CROSS HANDLE
(5)
as shown.
Install CROSS HANDLE
(5)
onto VALVE STEM
(3)
and
tighten HANDLE SCREW
(6)
.
Insert HOT INDEX
(7)
into
left CROSS HANDLE and COLD
INDEX
(8)
into right CROSS
HANDLE
(5)
.
For Diverter handle:
Install DIVERTER HANDLE
(9)
onto VALVE
STEM
(10)
of DIVERTER. Secure with DIVERTER HANDLE SCREW
(11)
. Thread HANDLE CAP
(12)
onto DIVERTER HANDLE
(9)
.
For Lever Handles:
Install
FRICTION WASHER
(1)
onto
base of LEVER HANDLE
(2)
.
Turn VALVE to off position and
align LEVER HANDLE
(2)
as
shown. Install LEVER HANDLE
(2)
onto VALVE STEM
(3)
and tighten SET SCREW
(4)
with HEX WRENCH supplied.
JADO
JADO
1
Apply putty to the underside of SPRAY BODY
FLANGE
(3)
and install SPRAY BODY
(3)
into
spray hole of Bidet.
From underside of Bidet install RUBBER WASHER
(4)
,
FIBER WASHER
(5)
and LOCKNUT
(6)
onto shank of SPRAY
BODY
(3)
. Tighten LOCKNUT
(6)
to make water tight seal.
4
8
5
6
7
7
Connect water supplies to FAUCET
(1)
with
1/2" IPS FLEXIBLE SUPPLIES
(2)
or 3/8"
O.D. BULL-NOSE RISERS
(3)
. Use adjustable
wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to
proper length.
Supply connections are made after bidet
has been installed.
3
2
HOT
HOT
COLD
FRONT
COLD
FERRULE
COUPLING
NUT
1
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED
AND HAVE TO BE PURCHASED SEPARATELY.
WATER SUPPLY CONNECTIONS
APPLY SEALANT
OR TEFLON TAPE
4
A FOAM SEAL
(1)
is installed on underside of FLANGE
(2)
. (Plumbers
Putty may be used in place of FOAM SEAL
(1)
if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE
(10)
and
thread into DRAIN BODY
(7)
making a water tight seal.
Drop FLANGE
(2)
into LAVATORY DRAIN
(3)
. From below assemble
RUBBER GASKET
(4)
, PLASTIC WASHER
(5)
and LOCK NUT
(6)
onto
DRAIN FLANGE
(2)
. Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4c
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER
(13)
height by repositioning POP-UP ROD
(16)
in SWIVEL
(15)
and tightening SET SCREW
(18)
.
Assemble POP-UP SWIVEL
(15)
to PIVOT ROD
(11)
but do not tighten.
Drop POP-UP ROD
(16)
through other hole in POP-UP SWIVEL
(15)
and
tighten SET SCREW
(17)
Assemble PIVOT ROD
(11)
,WASHER
(20)
and PIVOT NUT
(12)
as shown. Install
CONCAVE WASHER
(19)
into PIVOT ROD OPENING
(9)
if not preinstalled.
Hand tighten PIVOT NUT
(12)
. Drop STOPPER
(13)
into drain.
(
To vandal proof drain rotate STOPPER
(13)
so PIVOT ROD
(11)
goes
through EYE
(14)
of STOPPER
(13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY
(7)
that SEAL
(8)
is installed. Thread
DRAIN BODY
(7)
tight against FLANGE
(2)
to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
20
The PIVOT ROD OPENING
(9)
in DRAIN BODY
(7)
should face the rear
of the lavatory. Tighten LOCK NUT
(6)
on FLANGE
(2)
to make a water
tight connection with channel locks. Do not over tighten.
