JADO
JADO
1
Turn off hot and cold water
supplies before beginning.
CAUTION
ROUGHING-IN DIMENSIONS
2
FRONT
4
1
3
5
12
11
10
13
14
6
7
15
8
9
2
3
4
1
H 9 6 5 12 5 F
INSTALL TRANSFER VALVE
2
3
INSTALL CONTROL VALVES
Place LOCKNUTS
(10)
, FRICTION WASHER
(11)
and RUBBER
WASHER
(12)
onto the VALVE BODIES
(13)
. Insert VALVE BODIES
(13)
through valve mounting holes from underside of the BIDET LEDGE.
Insert HANDLE ESCUTCHEON
(14)
with SEAL WASHER
(15)
until snug against internal stop.
Set VALVE BODIES
(13)
so that their outlets are facing toward
DIVERTER
(2)
. Rotate VALVE BODIES
(13)
about 10 degrees from
center and tighten LOCKNUT
(10)
using wrench to secure VALVES
(13)
.
Apply sealant or Teflon tape to threads of SPRAY ELL
(1)
and install
into TRANSFER VALVE
(2)
.
Note: Arrow on SPRAY ELL
(1)
points
down, see illustration.
Install "Y" HOSE ADAPTER
(3)
with SEAL
(4)
to bottom nipple of
TRANSFER VALVE
(2)
and tighten to make a water tight seal.
Install LOWER CONE SEAL
(5)
onto TRANSFER VALVE
(2)
and
insert TRANSFER VALVE
(2)
from under side of Bidet into the
center forward hole.
Install UPPER CONE SEAL
(6)
, FRICTION WASHER
(7)
and
MOUNTING NUT
(8)
onto TRANSFER VALVE
(2)
.
Tighten MOUNTING NUT
(8)
to secure the TRANSFER VALVE
(2)
and make a water tight seal.
Thread TRANSFER VALVE ESCUTCHEON
(9)
onto MOUNTING
NUT
(8)
until snug against bidet ledge.
COLD
HOT
BIDET
LEDGE
64-152mm
2-1/2" - 6"
64-152mm
2-1/2" - 6"
44mm 1-3/4"
MAX 4"
27mm
1-1/16" D.
178mm
MAX 7"
51mm
MAX 2"
279mm
11"
54mm
2-1/8" D.
32mm
1-1/4" O.D.
SPRAY
29mm
1-1/8" D.
60mm
2-3/8" D.
62mm
2-7/16" D.
330mm
13" MAX
DIVERTER
AND VACUUM
BREAKER
LIFT ROD
CONNECTIONS ARE FOR 13mm
1/2" IPS FLEXIBLE SUPPLIES or
86mm 3/8" O.D.
BULL-NOSE RISERS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
APPLY SEALANT
OR TEFLON TAPE
Note: VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Remove LIFT ROD NUT
(1)
, METAL WASHER
(2)
and
RUBBER SEAL WASHER
(3)
from LIFT ROD GUIDE
(4)
.
Drop LIFT ROD GUIDE
(4)
into rear hole of bidet.
From below install RUBBER SEAL WASHER
(3)
, METAL
WASHER
(2)
and secure guide assembly with LIFT ROD NUT
(1)
.
LIFT ROD GUIDE INSTALLATION
10˚
10˚
3-1/8"
(78 mm)
3"
(75mm)
3-1/2"
(90mm)
4-1/8"
(104mm)
4-1/8"
(104mm)
3-1/2"
(90mm)
STRAIGHT
LEVER
HANDLE
CRYSTAL
LEVER
HANDLE
