background image

*SteamPro supplied with NEMA 6-50P plug.  NEMA 6-50R receptacle required.

Product specifications are subject to change without notice.

SPECIFICATIONS

DIMENSIONS

60"

(1524 mm) L

32"

( 813  mm) W

18-5/8"  ( 473  mm) H

TOTAL WEIGHT/

FLOOR LOADING

310 lbs
(141 kg)
/23 lb/sq. ft.
(112 kg/sq. m)

PRODUCT
WEIGHT

110 lb
(50 kg)

ELECTRICAL

*230 VAC, 60 Hz.
40 AMP, 3 Wire
Requires a
Dedicated Separate
Circuit.

Important:  Read complete instructions before beginning installation.

Each shower base is shipped with a drain and stainless steel strainer

Remove the shower base from the carton.  Do not destroy the shipping carton until after satisfactory

inspection of the product.

Immediately upon receipt, inspect the base before installing.  Should inspection reveal any damage or defect in the

finish, do not install the base.  Damage or defect to the finish claimed after the base is installed is excluded from the
warranty.  Jacuzzi Whirlpool Bath’s responsibility for shipping damage ceases upon delivery of the products in good
order to the carrier.  Refer any claims for damage to the carrier.  For definitions of warranty coverage and limitations,
refer to the published warranty information packaged with the product.  Jacuzzi Whirlpool Bath is not responsible for
any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure.

Plan the installation in relation to the finished wall surfaces.  Take into account the dimensions of both the shower

base and the shower door enclosure to be used with it.

NOTE: Damage or defects which could have been discovered and repaired prior to installation and which are claimed
after final installation of the product are excluded from our warranty.

60"

16-5/8"

18-5/8"

TOP VIEW

SIDE VIEW

8-1/2"

32"

1" TILE FLANGE

(LEFT HAND UNIT SHOWN)

SERVICE

ACCESS

RECEPTACLE
LOCATION
(RECEPTACLE TO BE
ACCESSIBLE FROM
SERVICE ACCESS)

STEAM HEAD AND SHIELD

( PRE-INSTALLED AND

CONNECTED TO

STEAM GENERATOR)

LOCATION FOR

INCOMING WATER

SUPPLY LINE TO

STEAMER (INSTALLED

AND PREPLUMBED

WITH 3/8" COPPER

TUBINGTO STEAM

GENERATOR WITH

SHUT OFF VALVE)

SHUT OFF
VALVE

STEAM
GENERATOR

45-3/8"

2

Summary of Contents for Steam & Shower Base SEDONA





















Reviews: