Jacuzzi PURE AIR BATH SERIES Installation And Operation Instructions Manual Download Page 6

Pure Air

®

 Bath

Page 6 

www.jacuzzi.com

 

Installation and Operation

English

Inspection and Testing

Visual Inspection

All bathtub units are factory tested for proper operation and watertight connections prior to shipping. However, the unit 

must be retested by the installer prior to installation. Jacuzzi Luxury Bath is not responsible for any defect that could 

have been discovered, repaired, or avoided by following this inspection and testing procedure:

1

  Place the bathtub on a level surface, near appropriate electrical supply, water supply, and water drainage. A 

driveway is a suitable choice.

2

  Seal the drain with tape or a stopper and fill the bathtub to 2˝ (50mm) above the highest air hole.

3

  Allow bathtub to stand for 5 minutes. 

4

  Plug in blower and turn unit on. Confirm that all features function as described in the Operation section of this 

manual. Do not install the bathtub if bathtub fails to operate as described.

5

  Visually inspect all joints for leaks. Do not install the bathtub if leaks are detected.

6

  Return bathtub to box or otherwise protect from damage until time of installation.

1

  Remove the bathtub from the shipping carton. Be careful not to scratch the surface of the bathtub on exposed 

staples. Remove the staples or fold them into the carton. Retain the carton until satisfactory inspection of the 

product has been made. Do not lift the bathtub by the plumbing at any time; handle by the shell only. 

2

  Inspect the shell and bathtub components. Should inspection reveal any damage or defect in the finish or visible 

damage to any components, do not install the bathtub. Damage or defect to the finish claimed after the bathtub 

is installed is excluded from the warranty. Jacuzzi Luxury Bath’s responsibility for shipping damage ceases upon 

delivery of the products in good order to the carrier. 

3

  Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the 

published warranty information packed with the product or in the back of this manual.

Installation

A technical specifications manual has been included with your bathtub. The Technical Specifications Manual will 

 

contain pertinent information regarding your Jacuzzi Luxury Bath product. Locate the Technical Specifications Manual 

at this time. 

Bathtub Water and Operational Test

Summary of Contents for PURE AIR BATH SERIES





























































Reviews: