background image

J-Sha II Owner's Manual

4

Drain Information

A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the
house.  After opening the carton, inspect for damage.  A solvent weld type drain is included and must be installed as
shown.  The drain solenoid wiring plug must be connected to the control box prior to drain/overflow assembly.  The
plug position (Drain Solenid) is shown on the control box.  It is recommended that the tail pipe be installed on the drain
before the drain/overflow is installed on the bath.  Hand tighten and then use a wrench to tighten until the tail pipe does
not turn.  Follow the installation instructions provided with the drain/overflow kit to install the drain/overflow assembly.
Note:  the bath must be propped up due to the length of the tail pipe.

NOTE:  Watertight installation of the drain is the installer's responsibility.  Drain leakage is excluded from the
Jacuzzi Whirlpool Bath warranty of this product.

1-1/4" FLEXIBLE PIPE

SOLENOID WIRING
TO CONTROL BOX

1-1/2" RIGID PIPE
(NOT PROVIDED)

1-1/2" TO 1-1/4" BUSHING (2)

TO BACK JET
DRAIN HOSE

BACK JET MANIFOLD
DRAIN SOLENOID VALVE

SPRING
CLAMPS

60

°

Summary of Contents for J-SHA





















Reviews: