background image

PRELIMINARY ROUGH-IN

The floor structure beneath the unit must be able to

support a total weight of the unit and bather(s).
Refer to page 2, SPECIFICATIONS, for weight speci-
fications.  Refer to COMPONENT IDENTIFICATION
on page 4 to help identify parts.

STEP 1

Provide an opening in the subfloor no less than 5" x 5"

square.  This opening should be located on the center
lines of the shower base drain hole.

Install blocking in studwall for seat flange.

STEP 2

Remove the stainless steel strainer from the drain

assembly.  Disassemble the locknut and two gaskets
from the back of the drain assembly.  Apply a 1/4" bead
of caulking (silicone) to the drain hole and insert the drain
assembly.  Replace the rubber washer, fiber washer,
and lock nut in that order.  Hand tighten the locknut.
Remove excess sealant from finished side.

Apply a lubricant (common household liquid soap

works well) to the inside of the rubber seal of the drain
assembly.

STRAINER

DRAIN
ASSEMBLY

SILICONE
SEALANT

SHOWER BASE

RUBBER WASHER

FIBER WASHER

NUT

APPLY LUBRICANT

BASE INSTALLATION

INSTALLATION INSTRUCTIONS

STEP 3

If the subfloor is level, no other preparation is neces-

sary.  You can proceed to install the  shower base.  If the
subfloor is not level, level the subfloor by spreading floor
leveling compound, mortar, plaster or minimal expan-
sion structural foam with a minimum density of 5 lbs/
cubic feet 

EVENLY 

over 

ENTIRE 

area where base will

be installed.  The compound used 

MUST

 make contact

with the entire bottom surface of the base.  Both sides of
a joint or splice of subfloor should be level to each other.
Level and support waste pipe cutout area greater than 5"
x 5".  The base is 

NOT

 to be supported by the tile flange.

SPREAD MORTOR OR LEVELING

COMPOUND ETC EVENLY OVER ENTIRE AREA

45

° 

COPPER ELBOW

PROVIDED (2)

COPPER FITTINGS 
AND TUBING 
NOT PROVIDED

STUD
WALL

DETAIL 1

5"x5" OPENING (MIN. AS POSSIBLE)

2" WASTE PIPE

21"

CL

BLOCKING

5

Jacuzzi Whirlpool Bath

© 

  BZ00000    03/05

CAUTION:  A nonflammable protective barrier must
be placed between soldering work and base unit to
prevent damage to the base.

WATER SUPPLY ROUGH-IN

Summary of Contents for BZ00000





























Reviews: