background image

 

 

www 

|

 jacques.com.au 

Document Number 

|

 JED-0492 

Revision 

|

 1.0 

 Page 14 of 18 

 

AGENCY REGULATORY NOTICES 

FEDERAL COMMUNICATIONS COMMISSION NOTICE 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures: 

 

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.  

 

Consult the dealer or an experienced radio/TV technician for help. 

 

DECLARATION OF CONFORMITY FOR PRODUCTS MARKED WITH THE FCC 
LOGO (UNITED STATES ONLY) 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions:  

1.

 This device may not cause harmful interference.  

2.

 This device must accept any interference received, including interference that may cause 

undesired operation.  

 

For questions regarding this FCC declaration, contact:  

Jacques Technologies Pty Ltd 

PO Box 3542,  

South Brisbane BC QLD 4101, Australia  

Or, call 

+61 7 3846 8400

 

 

To identify this product, refer to the Part, Series, or Model number found on the product. 

 

CANADIAN NOTICE 

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing 
Equipment Regulations. CAN ICES-3(B)/NMB-3(B) 

 

Summary of Contents for JEM-4



















Reviews: