Jacobsen R311T-T4F Safety, Operation And Maintenance Manual Download | Manualshive

Page: 63 / 84

background image

MAINTENANCE 9

62

9.20.2 CIRCUIT BREAKERS ______________________________________________________

Open the two latches and remove the access panel on the right-side
console wall to check the circuit breakers.

CB1 - 10 Amp Ignition Switch Circuit Breaker

CB2 - 10 Amp Combination Gauge Circuit Breaker

CB3 - 10 Amp 4WD-Cruise Control Circuit Breaker

CB4 - 30 Amp Accessory Relay Circuit Breaker

CB5 - 30 Amp Lights Circuit Breaker

CB6 - 10 Amp Air Ride Seat Circuit Breaker

CB7 - 5 Amp Start Interlock Circuit Breaker

CB8 - 25 Amp Main Relay Circuit Breaker

CB9 - 10 Amp ECU Circuit Breaker

CB10 - 5 Amp EGR Circuit Breaker

9.20.3 RELAYS_________________________________________________________________

The relays are found below the control panel and the circuit breakers. Remove the
control panel hardware and move the control panel away from the fuel tank as far as
the wires will allow.

The R311T mower uses five different types of relays. The relays are almost the same
in appearance and connection, but are not interchangeable. Always replace the
relays with the correct relay.

K1 - 30 Amp SPST w/ Diode Engine Temp Relay (P/N 365963)

K2 - 30 Amp SPST w/ Diode Cruise Control Relay (P/N 365963)

K3 - 30 Amp SPST w/ Diode Hydraulic Oil Level Relay (P/N 365963)

K4 - 30 Amp SPST w/ Diode Horn Relay (P/N 365963)

K5 - 30 Amp SPST w/ Diode Accessory Relay (P/N 365963)

K7 - 30 Amp SPDT w/ Resistor Neutral Switch Relay (P/N 4284035)

K8 - 30 Amp SPDT w/ Diode Brake Switch Relay (P/N 4193880)

K9 - 30 Amp SPDT w/ Resistor Interlock Relay (P/N 4284035)

K10 - 30 Amp SPDT w/ Diode Fuel Cut-Off Relay (P/N 4193880)

K11 - 30 Amp SPDT w/ Diode Start Interlock Relay (P/N 4193880)

K13 - 40 Amp Main Relay (P/N 4271134)

K14 - 70 Amp Glow Plug Relay (P/N 4221100)

K15 - 40 Amp Start Relay (P/N 4271134)

K17 - 30 Amp SPST w/ Diode Left Wing Switch Relay (P/N 365963)

K18 - 30 Amp SPST w/ Diode Right Wing Switch Relay (P/N 365963)

CB3

CB2

CB1

CB4

CB5

CB10

CB9

CB8

CB7

CB6

10

10

10

30

30

10

5

25

10

5

K11
K10
K9
K8
K7

K17
K18
K15
K14
K13

K5
K4
K3
K2
K1

«
...
61
62
63
64
65
...
»

Summary of Contents for R311T-T4F





















































































Reviews:

No comments

Related manuals for R311T-T4F

EC Hydro Midsize

Brand: Ransomes Pages: 150

Brand: Yard Machines Pages: 72

Brand: Martha Stewart Pages: 12

Pro Z 100 Lapbar

Brand: Cub Cadet Pages: 28

Brand: MTD Pages: 20

Brand: Alamo Pages: 168

Craftsman 917.250262

Brand: Sears Pages: 60

Brand: ZIPPER MASCHINEN Pages: 65

Brand: McCulloch Pages: 100

Brand: FGM Pages: 33

Brand: Honda Pages: 24

Brand: Ryobi Pages: 20

Brand: Encore Pages: 28

Brand: Snapper Pages: 7

Brand: IDS Pages: 34

Brand: Alamo Pages: 110

Brand: Yazoo Pages: 29

Brand: Toro Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands