manualshive.com logo in svg

Jacobsen R311T-T4F, Safety, Operation And Maintenance Manual

Share
Download
Jacobsen R311T-T4F Safety, Operation And Maintenance Manual Download Page 32

6 CONTROLS

31

6.2.1 IGNITION SWITCH _________________________________________________________

The ignition switch has three positions, OFF, RUN and START. In the run 
position, the controller program is active and input and output circuits are 
monitored.

6.2.2  PARKING BRAKE SWITCH__________________________________________________

To engage the parking brake, move the orange lock toward front of mower and press 
the front of the switch. Parking brake light on combination gauge (See 6.2.17) will turn 
on. Operation of the cutting units operation is disabled with the parking brake engaged.

To disengage parking brake, press the rear part the switch. The parking brake light will 
turn off.

NOTE: Engine will not start with the parking brake switch in the OFF position.

6.2.3 HORN SWITCH ___________________________________________________________

Press the front of the switch to use the horn.

OFF

RUN

START

Summary of Contents for R311T-T4F





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands