background image

SAFETY, OPERATORS & MAINTENANCE MANUAL

en-56

9

ADJUSTMENTS

E

D

9.4

BLADE CHANGE

1.

Raise the deck so it is just clear of the ground.  

This will allow the setting pin D to lift clear of 

the arm and be easier to remove.

2.

Remove the pins at position D on both sides of 

the machine which lock the deck in its working 

position.

3.

Lift the cutter deck to its full height.

4.

Rotate cutter deck to the vertical position.

5.

Insert one of the height of cut pins at position 

(E) to lock deck in its vertical position.

6.

Remove blade bolt (A).

7.

Remove blade (B) from deck.

8.

Fit new blade.

9.

Replace blade bolt A to hydraulic motor 

spindle.

10. Tighten blade bolt with torque wrench (C) set 

to 95N-m (70 ft.-lb.) torque.

11.

Remove the pin which holds the cutter deck in 

the vertical position and return deck to its 

working position.

12. Refit the locking pins to position (D).

9.5

BLADE SHARPENING

Blades are extremely sharp and can cause 

severe cuts.  For your protection, hold blades 

with thick leather work gloves only.

WARNING

Summary of Contents for HR3300T























































































Reviews: