Jacobsen HR 5111 Maintenance Manual Download Page 32

Page: 32 / 150

HR-5111 4WD

USE JACOBSEN

HYDRAULIC FLUID

SEE MANUAL FOR

SPECIFCATIONS

PUSH TO LATCH

WING ARMS.

PULL TO RELEASE

THIS RADIATOR CONTAINS

ANTI-FREEZE

PROTECTED TO -26 F (-32 C)

Mix equal parts of clean water and a premium

quality ethylene glycol based anti-freeze to

maintain the boil over, rust and corrosion

protection.

Drain and discard coolant yearly. Read manual

for additional instructions.

Radiator is under pressure. Remove

cap slowly to avoid personal injury

WARNING

To prevent burns, do not touch

muffler or muffler shield.

Temperatures may exceed 150¡F (66¡C)

WARNING

To prevent serious injury

never disconnect or tamper

with the seat switch.

Read the manual for more information.

WARNING

Filter is under pressure. Remove

filter slowly to avoid bodily injury

WARNING

Fill oil tank to 2 inches below filler neck

DO NOT OVERFILL

CAUTION

IMPORTANT

Tow valve to be used in case of

emergency only. Excess towing

may damage hydraulic system.

Before towing vehicle, turn

valve 90 to de-clutch. Do not turn

valve while machine is in motion.

J-T 364907 CA

IMPORTANT

DO NOT USE STARTING

ASSIST FLUIDS

USE OF STARTING ASSIST FLUIDS IN THE

AIR INTAKE SYSTEM MAY BE POTENTIALLY

EXPLOSIVE OR CAUSE A "RUNAWAY"

ENGINE CONDITION. THIS COULD RESULT

IN SERIOUS ENGINE DAMAGE.

1. Leer el manual del operador. No permitir que

personas no capacitadas para ello usen la maquina

2. Mantenae los escudos en su lugar y la tornilleria

debidamente fijada.

3. Antes de limpiar, ajustar o reparar este equipo,

desengranar todas los mandos, aplicar el freno de

estacionamiento y apagar el motor.

4. Mantener las manos, los pies y la ropa alejados de

las piezas en movimiento.

5. No viajar como pasajeros ni llevar pasajeros en

maquinas sin asiento para ellos.

6. Mantener a las demas personas alejadas

7. Si no sabe leer ingles, solicitarle a otra persona que

le lea y explique el contenido de las etiquetas y del

manual de la maquina.

ADVERTENCIA

To avoid injury when working with battery

1. Always connect the black ground (–)

cable last and remove it first.

2. Keep sparks and flames away, and

avoid contatc with acid.

To avoid injury when jumping battery

1. Connect positive (+) terminal to

positive (+) terminal.

2. Connect negative (–) terminal on good

battery to frame of vehicle that

has dead battery.

DANGER

J-T 3002556 CA

Maintain fluid level in radiator recovery tank between

"Full" and "Low" mark when engine is cold.
Clear the radiator core & radiator screen of any dirt

or grass clippings.
Check the engine oil each time you stop for fuel.
Empty air cleaner dust cap daily.
Read operators manual for more detailed service

instructions.

Read Manual thoroughly before operating for maintenance instructions.

DAILY SERVICE INSTRUCTIONS

KEEP HANDS AND FEET AWAY

DANGER

OPERATING INSTRUCTIONS

READ MANUAL THOROUGHLY FOR OPERATING AND SAFETY INSTRUCTIONS.

REPLACEMENT MANUAL AVAILABLE FROM: JACOBSEN/TEXTRON, 1721 PACKARD AVENUE, RACINE WI, 53403.

TO START

TO TRANSPORT

TO MOW

TO STOP

1. Set Parking Brake.
2. Set Speed Control
treadle in neutral.
3. Place implement switch
in off position.
4. Set throttle at half
position.
5. For cold starting,
hold glow switch
for seven seconds,
release switch.
6. Turn ignition switch
to start position.

1. Place implement switch
in off position.
2. Raise cutting units
and engage transport
latches.
3. Release parking brake
4. Set throttle to
fast position.
5. Depress treadle
pedal for desired
ground speed.

1. Lower cutting units
to ground.
2. Set rocker switch
in cut position for
mowing (and reverse
position for
clearing
obstructions from
reels, ST-5111 only).
3. Place implement switch
in on position.
4. Release parking
brake.
5. Set throttle to fast
position.
6. Depress treadle
pedal for desired
ground speed

1. Set treadle pedal
in neutral position.
2. Place implement switch
in off position.
3. Set parking brake.
4. Set throttle to
slow position.
5. Turn ignition to
off position and
remove key.

TO BACKLAP (ST-5111 ONLY)

PARKING BRAKE

1. Engage parking
brake.
2. Start engine and
set throttle to
minimum idle speed.
3. Engage implement
switch for
backlapping.
4. Set desired rocker
switch to reverse,
set other switch
in center (OFF)
position.
5. With extreme caution,
apply lapping
compound with long
handled brush.