Jacobsen Fairway 250 JGZZ250 Operation And Maintenance Manual Download Page 44

Page: 44 / 99

en-43

CONTROLS

6.13

UNIT TRANSPORT STOPS__________________________________________

If you press the pedal (A) when you lift the cutting units,
the units 1 to 5 are lifted to the transport position.

If you press the pedal (B) when you lift the cutting units,
the units 6 and 7 are lifted to the transport position.

6.14

HOURMETER ____________________________________________________

The hour meter is found on the left of the steering tower
(A), above the parking brake. The meter records the
number of engine hours that have been run.

6.15

REEL STOP LEVER _______________________________________________

This control improves the movement of the cutting unit
over ground that is not level.

Summary of Contents for Fairway 250 JGZZ250




































































































Search results

Summary of Contents for Fairway 250 JGZZ250

Reviews:

Related manuals for Fairway 250 JGZZ250

Brands by name

Popular brands

Jacobsen Fairway 250 JGZZ250, Operation And Maintenance Manual

Search results

Summary of Contents for Fairway 250 JGZZ250

Reviews:

Related manuals for Fairway 250 JGZZ250

Brands by name

Popular brands