manualshive.com logo in svg

Jackson Hot Water Sanitizing Undercounter Dishmachines JPX-300NSU, Technical Manual

Share
Download
Jackson Hot Water Sanitizing Undercounter Dishmachines JPX-300NSU Technical Manual Download Page 40

34

SECTION 6: PARTS SECTION

RINSE TANK & COMPONENTS

JPX-300NSU Technical Manual

7610-002-75-96 Rev. E (08/16/2005)

40°F Rise

70°F Rise

Volts

Hz

Phase

Rinse Heater (8.2 KW)

Rinse Heater (10 KW)

460

60

3

4540-111-51-46

4540-002-29-82

Thermostat, High Limit

5930-011-49-43

Decal, High Limit 

9905-011-84-32

Thermostat, Rinse Tank

5930-121-71-29

Decal, Thermostat Regulating

9905-011-84-31

Dielectric Cover

5700-011-40-50

Thermostat Mounting Bracket 

5700-*011-81-64

The thermostat attaches with 2:

Screw, 6-32 x 3/8” Sems w/External Tooth Washer

5305-002-25-91

Rinse Tank Weldment 

5700-002-71-00

Secured with: Locknut, 1/4”-20 S/S Hex with Nylon Insert

5310-374-01-00

Gasket, Heater

5330-011-47-79

Fitting, 1/4” Imperial Brass

5310-924-02-05

Nut, 5/16”-18 S/S Hex

5310-275-01-00

Lockwasher, 5/16” Split

5311-275-01-00

The JPX-300NSU comes supplied with various heaters, depending on the characteristics of the machine. To ensure that you
order the correct heater for the model you are servicing, please refer to the following table:

Summary of Contents for Hot Water Sanitizing Undercounter Dishmachines JPX-300NSU
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands