background image

 
 

 

Plasma CUTTER 150 

 
 
 
 
 
 
 

General information’s: 

 

These operating instructions are intended to ensure safe and efficient work with 

 

this cutting unit. 

 
 

Prior to initial operation of the unit, read the instructions carefully. 

 
 

The information contained in this manual should be made available to all operational 

 

staff. These instructions should always be kept ready-to-hand, near the machine. 

 
 
 
 
 
 

Electromagnetic compatibility EMC (IEC 60974-10): 

 

WARNING: This class A cutting unit is not provided for use in housing areas, 

 

where the electric power supply comes from a public low voltage supply. 

 

It may possible, that through wire fixed or radiate disturbances, it isn’t easy to 

 

guarantee electromagnetic compatibility in these areas. 

 
 

INFORMATION: The user is responsible for the trouble, which the machine  

 

generates during the operation. He must rate and consider possible  

 

electromagnetic problems in the neighborhood. 

 
 
 
 
 
 

Warranty: 

 

INFORMATION: Improper repair or servicing, technical modifications of the 

 

product, unauthorized, not strictly from JÄCKLE GmbH permitted modifications, 

 

as well as carelessness at the installation or use, or the nonobservance of care 

 

in own affairs lead to the extinction of every warranty. 

 
 

Summary of Contents for 150


























Reviews: