The TP-82 wireless thermostat
2 / 2
MKL51103
Locking the thermostat
•
To prevent the accidental changing of the set temperature the
thermostat can be
locked by pressing and holding the knob
(for
about 2 seconds, the lock symbol will appear on the display).
•
To unlock the thermostat simply
press and hold the turning knob
(for about 2 seconds, the lock symbol will disappear on the display).
Integration into the OASIS system
•
The thermostat can also be
enrolled to a control panel as a
detector.
If the temperature decreases below
ALLo
a
panic
alarm
will be triggered =
frost threat
(heating failure).
•
If the temperature exceeds
ALHi
then a
fire alarm
will be triggered.
•
An AC-82 receiving unit has two output relays (X and Y). TP-82
thermostats can be enrolled separately to each relay (in enrollment
mode 4) in order to
control two independent heating circuits.
•
To operate a heating system the Oasis control panel
can also
be enrolled (sequence 299) to the same relay as the thermostat is
enrolled to. A thermostat enrolled to the X relay
can be operated
via the PGX programmable output,
and a thermostat enrolled to
the
Y
relay operated via
PGY.
If the programmable
output of the
control panel is switched on,
the thermostat maintains the set
temperature. If the control panel’s output is
switched off
the
thermostat only triggers heating if the temperature drops
below
InLo
(anti-freeze protection).
•
To operate the heating,
RC-80 or RC-88
remote controls
can
also be enrolled to a receiving unit (AC-82). The heating can be
switched on
by remote controls
to heat
to the desired temperature
and also
switched off where it only heats when the temperature
is below ALLo
.
•
To disable heating when windows are open
JA-80M or JA-82M
detectors
can also be enrolled to the same relay as the thermostat
is enrolled to
.
If the windows are closed it
heats
to the desired
temperature and if windows are open it
heats only when
temperature is below ALLo
.
•
Up to 8 thermostats
can be enrolled to a single relay. If at least
one thermostat transmits a heat command then the relay will be
switched on.
Battery replacement
Replace the battery when the low-battery symbol is displayed (or the
thermostat stops working). If the thermostat is enrolled to the control
panel, then a low battery will be indicated by the control panel (to the
user and installer). Use only AA 1.5V alkaline batteries.
RESET
The RESET function allows you to reset the device to factory defaults
listed in the table. You can perform RESET by selecting
Res
in the
adjustment menu and pressing and holding the knob for 5 seconds.
Specification
Power supply:
1x AA 1.5 V alkaline battery
Battery lifetime
typically 1 year
Temperature measurement:
+6°C to +40 ˚C
Temperature accuracy:
adjustable: ± 0.1, ± 0.2 or ± 0.5 ˚C
Freeze alarm (panic transmission) temperature threshold:
<ALLo
configurable from –9°C to +20°C
Fire alarm temperature threshold:
>ALHi
configurable from 30°C to 70°C
Operational frequency:
868 MHz, Oasis protocol
Operational radio range:
up to 100 m (open area)
Operational temperature range:
-10°C to + 70°C (low humidity)
Dimensions:
65 x 88 x 20 mm
Can be operated according to
VO-R/10/05.2006-22
Jablotron Ltd. hereby declares that the TP-82 is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/ES. The original of
the conformity assessment can be found on the web site
www.jablotron.com
, Technical Support section.
Note
: Dispose of batteries safely depending on battery type
and local regulations. Although this product does not contain
any harmful materials we suggest you return the product to
the dealer or directly to the manufacturer after use.
20
65
32.5
32.5
88
25
44
19
Internet: www.jablotron.com
Tel.: 483 559 911
fax: 483 559 993
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
