jablotron OASiS JA-82KRC Installation Manual Download Page 6

Page: 6 / 21

Installation manual: OASiS security system JA-82KRC

6 / 21

MKH51100_OS2

When equipped with a JA-82R module, the control panel also

allows for a JA-80F wireless keypad connection.

Modular connection

cable

Control and programming

keypad JA-80E

We recommend only having a single JA-80E hard-wired

keypad in the system.

6. Back-up

battery

It is possible to use a Jablotron-brand 12V back-up battery in

the control panel with a capacity of 2.2 Ah. The capacity to use
depends on the total power consumption of the system and the
desired back-up period.

Euro-standard EN 50131-1 specifies a 12 hour minimum

back-up time for grade 2 systems. The standby consumption of
all system devices is shown in

Table 1

•

With

2.2Ah

back-up battery 12 hours of back-up time can

be realised if current consumption does not exceed

150mA

This only takes 80% of the battery capacity into account as
20% has to be reserved for battery aging effects.

•

The average

back-up battery lifetime

up to 5 years

after which it must be replaced. The back-up battery is
automatically charged and its condition is monitored by the
system. If the system is being run on only the back-up
battery a technical alarm occurs when the battery is nearly
discharged. If the voltage gets too low the battery will be
disconnected. After the mains supply has been restored
battery charging starts again and the system will begin to
function again.

Table 1- standby consumption of system devices

Ensure that the battery is correctly connected (Polarity: RED =
po, BLACK = negative -).

WARNING – the battery is sold charged – to maintain safety,
avoid shorting out the terminals !!!

7. Powering-up the control panel for the

first time

•

First check all the wiring, and if a GSM communicator is

installed, insert its SIM card (PIN code disabled).

•

Carefully

connect

the back-up battery,

•

Carefully connect up the mains. A green LED will start

flashing on the control panel board.

•

If a hard-wired keyboard is connected it will indicate Service

mode. If not, the control panel is not set to the factory default
and should be reset (see section

7.1.

Wireless keypad enrollment

If no hard-wired keypad is connected to the control panel,

and the wireless keypad was not supplied as part of a JK kit,
the wireless keypad must be enrolled to the control panel as
follows:

1. Have an opened keypad and its battery ready.
2. Check that the green LED in the control panel is flashing.
3. Short the reset link in the control panel for 1 second (e.g.

using a screwdriver). This will enter enrollment mode on the
control panel.

4. Install batteries into the keypad not far from the control

panel.

5. The keypad generates a beep sound and enrolls to address

05 (or 15). After that it indicates “Enrollment 06: Device” (or
“Enrollment 16: Device”).

6. Press the

key to exit enrollment mode and “Service” will

be indicated on the keypad.

Warning:

•

If the keypad does not enroll, then the control panel settings

are not the factory-defaults. In this case perform a reset and
repeat the enrollment procedure.

•

If you want to assign the keypad to another address, re-

enter enrollment mode via the “1” key, then use the arrow
keys to select the desired address. Then disconnect the
keypad battery and reconnect it.

Recommendation: it is highly recommended to install the
wireless keypad with a magnetic door sensor wired to its hard-
wired input terminal. This way the keypad will wake up every
time after opening the door and it will produce entrance delay
beeps and will be ready to read access cards. It will also save
money on a wireless door detector.

8. Language selection of the keypad

If the

∗

key is kept pressed during battery connection, the

internal keypad menu will be displayed allowing the selection
of the

desired language

. Using the arrows, choose your

language and confirm selection by the

∗

key.

In this menu the

door bell function