JK-16 PROFI
2/4
MGK24401
4. Detector and accessory installation
a) Install the
JA-60N magnetic detector onto the door
(antenna pointing up or down)
b) Install the
JA-60P PIR motion detector
c) Select
Instant or Delay reactions
via the DIP switches
inside the detectors.
d)
Connect the detector’s batteries
(pull out the red tape to
activate the batteries)
e)
Attach the keypad to the desired location
f) Plug the UC-260
wireless siren
into a power socket
g) Test the wireless
doorbell button
and install it.
5. Enrollment of additional accessories
If you install
additional detectors
(max. 32), you have to enroll
them. The system should be in
P mode
(if not enter F0 6060):
a)
Press 1 to enter enrollment
mode*
b)
The next free
detector
position will be displayed on the
keypad.
c)
Install batteries
into all new detectors step by step to enroll
them (system will automatically offer the next free position)
d) To
scroll through sensor positions,
press 1 (up) or 7 (down)
e) To enroll a
second detector
to an occupied position press 5
before you install the detector’s batteries
f) To
exit enrollment
mode
press the N key
The wireless keypad
(JA-63F) enrolls after you install its
battery while in
enrollment
mode.
The remote control
(RC-4x) enrolls after you press and hold
both
and
buttons while in
enrollment
mode.
The wireless outdoor siren
(JA-63A) enrolls after it is
powered up while in
enrollment
mode
To enroll the control panel to UC receivers
enter
299
on
the keypad while in P mode
Check individual device manuals for more details
•
*Enrollment mode will also start after shorting the reset pins
in the control panel while it is in P mode.
6. Detector and controller testing
a) The system should be in
P mode
(if not enter F0 6060)
b)
Trigger detectors
– their addresses (1=door and 2=PIR) should
be indicated (if the PIR detector does not react, re-enter test
mode by opening and closing its cover)
c) Press
button
on the RC-4x remote control
–
c2
will be
indicated
7. To measure the strength of the radio signal
a) While in
P
mode, press
1
and then using
7
scroll to position
1
b) Press
8
to start measuring
c)
Activate
the door detector to view its signal strength
d) Using the
1 key, scroll to the next position
(2 PIR) and
check its signal strength (if the PIR detector does not react,
reenter its test mode by opening and closing its cover)
e) Repeat step d) to check all enrolled items. The
wireless keypad
(c1) signal is indicated after you trigger its tamper.
The
remote
control
(c2) is indicated after you press it’s
button.
f) Change the location of an item if its signal is
lower than 2
g)
Return to P
mode by pressing the
N key
8. Programming the system
a) The system should be in
P mode
(if not enter F0 6060)
b) Using the following sequences you can program:
Function
Sequence
Comments
Your
installer code*
5 xxxx xxxx
6060
factory default
xxxx new code
Exit delay
20x
3
=30sec factory def.
Entrance delay
21x
3
=30 sec factory def.
Alarm duration
22x
4
=4min factory def.
Time & date
4 hh mm DD MM YY
See control panel installation manual for more details.
•
Must be changed
•
9. Finishing the installation
a) Fill in the information on the sticker label and attach it inside
the keypad cover.
b) Switch the system to standby (by pressing the N key)
c) Instruct the user on how to operate the system
A
attach
C
open
B
click
rear tamper
lever
Don't tight
this screw
2
2,5
1,5
1
0,5
1,6
3,7
12
range [m]
height
[m]
120
ş
12
m
zone A
zone B
zone C
zone A
zone B
zone C
JA-60P coverage
avoid locations against windows or close to a heater