JABLOTRON
ALARMS
a.s.
Pod
Skalkou
4567/33
46601
Jablonec
n.
Nisou
Czech
Republic
www
.jablotron.com
||
|
JA-163A RB Wireless outdoor battery-powered siren
JA-163A RB Wireless outdoor battery-powered siren
1 / 2
MNM51103
The JA-163A RB is a component of the
JABLOTRON 100
system.
It is used for system alarm indication outside a building. It can also be used
for supplementary acoustic signalling (PG activation, arming, chirps).
The siren is powered by just one lithium battery with no other external
power. The JA-163A RB includes only the base with the
JA-163A-BASE-
RB
PCB, the BAT-100A lithium battery and always has to be completed
with a cover from the
JA-1X1A-C-xx
series (see following table). The siren
occupies one position in the system. The product should be installed by
a trained technician with a valid certificate issued by an authorized
distributor.
For combinations of colour and cover material, see the following table:
Cover type
Colour and cover
material
Strobe colour
JA-1X1A-C-GR
Grey plastic
Red
JA-1X1A-C-ST
Stainless steel sheet
JA-1X1A-C-WH
White plastic
JA-1X1A-C-GR-B
Grey plastic
blue
JA-1X1A-C-ST-B
Stainless steel sheet
JA-1X1A-C-WH-B
White plastic
Installation
The whole enrolment procedure has to be done in service mode
of the control panel. There must be a JA-11xR radio module installed
in the control panel.
Figure 1: 1 – hole for installing; 2 – piezo sounders; 3 – BAT-100 lithium battery
with reusable battery strap (up to 2 batteries can be used); 4 – PCB;
5 – spirit level; 6 – hole for installation with tamper detection; 7 – front cover
screw; 8 – string with clip connecting the front cover for easy installation
The siren should be installed on a vertical
wall, with the flasher facing downwards.
Avoid installing the siren near the gutters and
on other places where there is a danger of ice
accumulation.
1.
Attach the siren onto a suitable place using 2 screws through
the holes (1) and (6). The spirit level can be used for easy
installation (5).
2.
Connect the BAT-100A lithium battery (3) to the connector (11).
3.
Proceed according to the control panel installation manual.
Basic procedure:
a.
When the battery is connected, the yellow LED (12) indicates
by a permanent light that the siren has not been enrolled into
the system yet.
b.
Go to the
F-Link
software, select the required position
in the
Devices
tab and launch the enrolment mode by clicking on
the
Enroll
option.
c.
Press the button marked LEARN (10) – the siren is thus enrolled
and the yellow LED indicator goes off.
4.
Put back the siren cover and attach it using the screw (7).
5.
Perform siren properties setting, see the following chapter: Internal
settings of the siren.
Notes:
The siren can also be enrolled into the system by entering
its production code (9) in the F-Link software. You can find
the production code on the sticker, glued on the PCB.
All numbers under the bar code shall be entered (1400-00-0000-
0001).
The siren can be powered by up to two BAT-100A batteries and we
recommend this when longer siren operation time is required.
There is a place prepared for second battery use see Figure 1.
Connect the battery to the other connector (11). The battery connection
order doesn´t matter.
Figure 2: 9 – production code; 10 – LEARN (enrollment) button;
11 – battery connector; 12 – yellow fault indicator; 13 – mini USB connector;
14 - piezo siren connection (attention: high voltage);
15 – external antenna connector; 16 - high intensity red LED flashers
Erasing the siren from system / RESET
Use this procedure when the siren has to be erased from one system
and enrolled to another one. Proceed this way:
1. The control panel has to be in
Service
mode.
2. Open the siren cover and disconnect the BAT-100A battery from
its connector.
3. Go to the F-Link software,
„Devices“ tab,
and erase the siren from
the control panel and
leave service mode
.
4. Connect the BAT-100A battery. Then press and hold the LEARN
button (10) for approximately 8 sec until the yellow LED (12) starts
flashing. Then release the button.
5. When flashing expires (2 x 7 flashes) the yellow LED illuminates.
This indicates that the siren is not enrolled.
Notes:
-
When a reset is done the yellow LED goes off and it means that
there is some control panel in the siren’s radio range with
an open service mode and the enrollment procedure has been
performed again and the siren is assigned to that control panel.
FW update
1. A FW update can be performed by the F-Link software in service
mode, but only by a user with
Service
authorisation.
2. Start the F-Link software and enter service mode.
3. Open the siren cover.
4. Do not disconnect the battery!
5. Connect a PC to the siren using a mini USB cable.
6. FW update mode is indicated by the flickering of the yellow LED.
7. Continue as with updating the control panel using F-Link software;
F-
/LQN&RQWUROSDQHOĺ8SGDWHILUPZDUH
. In the device options
select the USB option (typically at the first position).
8. Press the
OK
button to perform an update of the selected device.
9. Disconnect the mini USB cable.
10. Close the siren cover.
11. Check the siren settings via
F-Link SW, Devices / Internal
settings
.
12.
Test the siren functions.
Notes:
A mini USB cable is not in the supplied accessories of the siren, control
panel or any other device. You can use the cable from
the JA-190T card reader. We strongly recommend connecting
the USB cable straight to the PC connection as using a USB HUB can
reduce the reliability.
According to the changes which have been done during the update,
previous settings might stay or settings could be erased to default.
When a reset has been done you can reload the previous settings
by the Import button and restore them with no negative influence
on the new firmware.
Internal settings of the siren
The siren properties can be set in the
Devices
window of the F-Link
software. When at the siren position, use the
Internal settings
option
