The JA-152J MS Bi-directional two-button keyfob
The JA-152J MS Bi-directional two-button keyfob
2 / 2
MMJ54102
door control), it is necessary to mind that the action is
performed first.
The
acoustic indication
can be disabled by simultaneous pressing
and holding the pair of buttons (A+B) until the yellow LED (1) starts
flashing briefly for the second time, usually in 6 s. When the yellow
LED (1) flashes a second time release the button (B) and press it again.
The acoustic indication is then disabled and confirmed by flashes of the
yellow LED and a one beep. After this confirmation release all buttons.
The
acoustic indication
can be enabled by repeating the procedure
above. Activation is confirmed by a double flash of the yellow LED and
a double beep.
LED indication table
Action
Indication
Pressing the button is always indicated by a very short flash of the
yellow LED and followed by flashing of the coloured LED according to
the performed action.
The mentioned indication statuses are valid for the remote’s default
setting.
Unsetting
Control
function
with
confirmatio
n by LED
2 s flash of green LED
and 2x short acoustic signals
Setting
2 s flash of red LED
and 1x short acoustic signal
Partial setting
2 s flash of yellow LED
and 1x short acoustic signal
Unsetting after an
alarm
2 s flash of green LED
and 3x short acoustic signals
Delayed panic
Flashing of red LED
until action is done or its
cancelling
Setting confirmation
request
Flashing of red LED
until confirmation (max. 8 s)
Partial setting
confirmation request
Flashing of yellow LED
until confirmation (max. 8 s)
Pressing of button with no function
or lost communication
Short flash of yellow LED
1x short acoustic signal
Low battery
Flashing of yellow LED
3x short acoustic signals
Holding the button – Copy PG
1x short acoustic signals,
red LED lights for whole
period of button being
pressed
Table 2. Remote control indication
Battery replacement
Low battery indication is signalled on the remote control after any
button is pressed. The action assigned to the button is done and the
yellow LED flashes with 3 quick beeps. Low battery information is also
sent to the control panel. The remote still works as usual but the RF
range goes slowly down. Low battery indication is cancelled when a
new battery is inserted.
To change the battery, unscrew the 2 screws from the back plastic;
remove the cover with the metal strut from the housing and remove the
discharged battery. Then press any button a few times to discharge the
rest of the energy from the capacitors and insert a new battery.
Battery replacement DOESN´T RESET the keyfob settings nor
the locks nor the acoustics
.
Don´t throw a used battery into the trash but take it to a suitable
recycling station.
Technical specifications
Compatible with:
FW of the JA-11xR module
FW of the control panel LJ(MD)60416+
F-Link 1.4.0+
Power – lithium battery
type CR 2032 (3.0 V/0.2 Ah)
(Power supply C type according to EN 50131-6)
Low battery voltage detection
2.2 V
Typical battery lifetime
approx. 2 years (10 activations/day)
Communication frequency
868.1 MHz
RF range
approx. 300 m (line of sight)
Dimensions
63 x 36 x 15 mm
Weight with no battery
32 g
Classification
Security grade 2/Environmental class II
- according to
EN 50131-1, EN 50131-3 (digital key)
- number of unique production codes
> 1 Million
- environmental
Indoor general
- operational temperature range
-10 °C to +40 °C
- average humidity
75 % RH, non-condensing
- certification body
Trezor Test s.r.o. (no. 3025)
Also complies with
ETSI EN 300 220, EN 50130-4,
EN 55022, EN 60950-1
Can be operated according to
ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the JA-152J
MS is in a compliance with the relevant Union harmonisation
legislation: Directives No: 2014/53/EU, 2014/35/EU,
2014/30/EU, 2011/65/EU. The original of the conformity
assessment can be found at www.jablotron.com - Technical
Support section.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use
.
If the remote control is out of the RF range
of the radio module or MPR, it doesn´t
indicate status change or signal loss.
