IXXAT PC-I 04/104 Hardware Manual Download Page 2

 

 
 

 

 
 

 
 

 
 

 

 
HMS Technology Center Ravensburg GmbH 

Helmut-Vetter-Straße 2 
88213 Ravensburg 
Germany 
 
Tel.: +49 751 56146-0 
Fax: +49 751 56146-29 
Internet: www.hms-networks.de 
E-Mail: [email protected] 
 
 

Support 

For problems or support with this product or other HMS products please 
request support at www.ixxat.com/support. 
 
Further international support contacts can be found on our webpage 
www.ixxat.com 
 
 

Copyright 

Duplication (copying, printing, microfilm or other forms) and the electronic 
distribution of this document is only allowed with explicit permission of HMS 
Technology Center Ravensburg GmbH. HMS Technology Center 
Ravensburg GmbH reserves the right to change technical data without 
prior announcement. The general business conditions and the regulations 
of the license agreement do apply. All rights are reserved. 
 
 

Registered trademarks 

All trademarks mentioned in this document and where applicable third 
party registered are absolutely subject to the conditions of each valid label 
right and the rights  of particular registered proprietor. The absence of 
identification of a trademark does not automatically mean that it is not 
protected by trademark law. 
 
 
 
 
Document number: 4.01.0070.20000 
Version: 2.7 

 

Summary of Contents for PC-I 04/104

















Reviews: