IVC Displays NP-610X User Manual Download Page 15 | Manualshive

Page: 15 / 32

background image

15

COM3 [RS-485] connect
RS-485 2 wire Device

NP-610X
COM1 [RS-485]
9P D-SUB Female

RS-485 2 wire Device

4

Data+

Data+

5

Data-

Data-

1

GND

COM3 [RS-485] connect
RS-485 4 wire Device

NP-610X
COM1 [RS-485]
9P D-SUB Female

RS-485 4 wire Device

1

Rx-

Tx-

RS485 Transmit

2

Rx+

Tx+

RS485 Transmit

3

Tx-

Rx-

RS485 Receive

4

Tx+

Rx+

RS485 Receive

5

GND

2.3.3 USB Master port

The USB Master port can connect USB mouse and USB keyboard.

The USB Master port support USB 2.0 full-speed host (12Mbps).

This port support USB Mass storage device. But the USB hard disk must use external power.

«
...
13
14
15
16
17
...
»

Summary of Contents for NP-610X

































Reviews:

No comments

Related manuals for NP-610X

Brand: NI Pages: 11

XpressNet Digital plus LA152

Brand: Lenz Pages: 2

Brand: LAKS Pages: 24

Brand: ETM Pages: 8

Brand: Enfora Pages: 3

Terminal Block NI TB-2706

Brand: National Instruments Pages: 8

Brand: National Instruments Pages: 8

Brand: Invenco Pages: 40

Brand: Telic Pages: 27

Brand: e-Taxfree Nordic Oy Pages: 14

AKI-CDF-MOD-10T

Brand: Kollmorgen Pages: 28

Brand: EBN Pages: 45

Brand: ZKTeco Pages: 55

Brand: ZKTeco Pages: 39

DS-K1T342 Series

Brand: HIKVISION Pages: 205

Brand: Bouyer Pages: 17

Brand: ATEN Pages: 48

Brand: PaceBlade Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands