ITT McDonnell & Miller FS8-W Series Installation & Maintenance Download Page 2

2

NOTE:

Switch on ‘G’ models is rated for 300 watts @ 125VAC.

Maximum Liquid Pressure:

160 psi (11.3 kg/cm

2

)

Liquid Temperature  Range  (T

L

):

32 - 225˚F (0 - 107˚C)

Ambient Temperature  Range  (T

S

):

32 - 120˚F (0 - 49˚C)

Electrical Enclosure Rating:

Nema Type 4X (IP 56)

Maximum Velocity:

10ft/sec (3M/sec)

Pipe Connection Thread Size:

- 1" NPT 

- All models 

except “J”

- 1" BSPT 

- “J” models

• This Control:

is for continuous operations
is not electronic
has Type 1C action (micro 
interruption on operation)

• LVD 73/23/EEC

• EMC 89/33/EEC

For applications with loads between 0.5 and 3.7 Amps,
power factors exceeding 0.65, an anticipated system
switch operation rate of less than once per 2.5 minutes,
and any one cycle greater than 3 seconds on and 3 
seconds off.

For applications with loads 0.5 and 38mA, power
factors exceeding 0.65, an anticipated system switch
operation rate of less than once per 5 minutes, and any
one cycle greater than 3 seconds on and 3 seconds
off.

Additional suppression may be required for applica-
tions outside these ranges.

• Declaration of Conformity

Available on request.

SPECIFICATIONS

CE Circuit Rating

7.4 (7.4)/120~

0.3/120=

3.7 (3.7)/240~

0.15/240=

Motor Switch Rating (Amperes)

Voltage

Full Load

Locked Rotor

Pilot Duty

120 VAC

7.4

44.4

125 VA at

240 VAC

3.7

22.2

120 or 240 VAC

50 or 60 cycles

ELECTRICAL RATINGS

Models that meet CE Conformance:
FS8-WJA-E

Summary of Contents for McDonnell & Miller FS8-W Series









Reviews: