ITT Goulds Pumps IC Installation, Operation And Maintenance Manual Download Page 73

Page: 73 / 97

922

412.21

230

Figure 36: Impeller removal method

NOTICE:

•

Remove shaft guard using a prying tool.

•

Be sure to align the pry bars with the impeller vanes in order to prevent damage to
the impeller.

Remove the impeller key (940.31).

Place the back pull-out assembly in a vertical position before you proceed with the disassembly.

922

412.21

230

210

940.31

Figure 37: Rotor components

NOTICE:

Crush hazard. Make sure that the back pull-out assembly cannot tip over.

6.4.8 Remove the seal-chamber cover

Remove the gland stud nuts.

Remove the seal-chamber stud nuts.

Remove the seal chamber (161).

Remove the shaft sleeve (524) if it is used.
The mechanical seal is attached to the sleeve.

6.4 Disassembly

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps IC


































































































Search results

Summary of Contents for Goulds Pumps IC

Reviews:

Related manuals for Goulds Pumps IC

Brands by name

Popular brands

ITT Goulds Pumps IC, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps IC

Reviews:

Related manuals for Goulds Pumps IC

Brands by name

Popular brands