ITT Goulds Pumps HSUL Installation, Operation And Maintenance Manual Download Page 21 | Manualshive

Page: 21 / 26

background image

5 Maintenance

5.1 Disassembly

5.1.1 Disassemble the pump

1.

Disconnect all electrical service. Mark leads for reassembly.

2.

Remove fasteners which secure casing (100) to motor adapter (340) and separate the parts.

3.

Remove impeller cap screw (370C) and impeller washer (528J). Impeller is keyed to shaft. Carefully
slide impeller off shaft.

4.

Remove fasteners attaching motor adapter (340) to motor (9700) and separate parts.

Figure 5: HSUL pump

NOTICE:

The motor shall be disassembled only by an authorized repair center. Failure to comply will re-
sult in voiding warranty.

For motor instructions see ABB/Baldor/Reliance Electrical Manual B-3629.

Table 3: Standard parts

Item

Qty / Pump

Part

100

1

Casing

5 Maintenance

HSUL Installation, Operation, and Maintenance Manual

19

«
...
19
20
21
22
23
...
»

Summary of Contents for Goulds Pumps HSUL



























Reviews:

No comments

Related manuals for Goulds Pumps HSUL

Brand: GE Pages: 28

Brand: Zehnder Pumpen Pages: 24

Brand: Gardena Pages: 8

Brand: Laser Pages: 4

Brand: Valeo Pages: 88

Brand: Valdemar Energy Pages: 61

Brand: Tebas Pages: 14

Brand: Immergas Pages: 40

Goulds CentriPro M05411

Brand: Xylem Pages: 68

Feeder/Deliming System EV9797-20

Brand: Everpure Pages: 2

Brand: Edwards Pages: 60

AQUAJET PFN 10000 PLUS

Brand: Aquael Pages: 54

Brand: ThermoFlow Pages: 34

Brand: Okay Pages: 52

Milton Roy Milroyal Series

Brand: Accudyne Industries Pages: 68

Brand: Lamborghini Caloreclima Pages: 62

Brand: FLOJET Pages: 4

Brand: Macon Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands