ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 85 | Manualshive

Page: 85 / 178

background image

412A

Figure 56: O-ring for model CV 3196

If the impeller cannot be removed by the previous methods, cut the shaft between the gland and the
frame, remove the impeller, stuffing-box cover, gland, sleeve, and shaft end as a unit. Do not apply heat.

6.4.8 Shaft guard removal (if provided)

6.4.8.1 Remove the shaft guard (STi)

1.

Remove the bolt for each shaft guard half that mounts the halves to each side of the frame.

2.

Do not remove the clip that retains the bolt on the guard to maintain a captive fastener.

3.

Retain each guard half with fasteners for reinstallation.

1

2

Item

Description

1.

Retaining clip (do not remove)

2.

Mounting bolt

Figure 57: Shaft guard installation

6.4.8.2 Remove the shaft guard (MTi/LTi, XLTi/i17)

1.

Remove the bolt for each shaft guard half that mounts the halves to the brackets on each side.

2.

Do not remove the clip that retains the bolt on the guard half to maintain a captive fastener.

3.

Do not remove the brackets from each side of the frame adapter.

6.4 Disassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

83

«
...
83
84
85
86
87
...
»

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Reviews:

No comments

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brand: Wacker Neuson Pages: 38

Brand: KISANKRAFT Pages: 44

Brand: Rinnai Pages: 2

Brand: Bard Pages: 38

Brand: SFA-SANIFLO Pages: 14

Brand: WACKER Group Pages: 66

Brand: Grundfos Pages: 153

VRV III RXYQ5-54PY1

Brand: Daikin Pages: 398

Brand: NAKAYA Pages: 47

URG250H6N-475-264

Brand: Bradford White Pages: 32

Brand: Laars Pages: 36

Water Quality System EQHP-TWIN 108SP

Brand: Bunn Pages: 2

Brand: ICP Pages: 4

Brand: IWAKI PUMPS Pages: 21

PowaPak ZA4208TX-QR0P

Brand: Enerpac Pages: 24

Brand: Excalibur Water Systems Pages: 32

evotherm EFI Ultra V30T

Brand: Evolution Pages: 48

Brand: Camus Hydronics Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands