ITT GOULDS PUMPS 3296 EZMAG Installation, Operation And Maintenance Manual Download Page 38

Page: 38 / 100

Check

Explanation/comment

Checked

If quick-closing valves are installed in the
system, check that cushioning devices are
used.

This protects the pump from surges and water hammer.

Example: Discharge piping equipment

Correct

Incorrect

Bypass line

Shut-off valve

Check valve

Discharge isolation valve

Check valve (incorrect position)

The isolation valve should not be positioned be-
tween the check valve and the pump.

4.5.5 Final piping checklist

WARNING:

A build-up of gases within the pump, sealing system, or process piping system may result in

an explosive environment. Make sure the process piping system, pump and sealing system are
properly vented prior to operation.

Check

Explanation/comment

Checked

Check that the shaft rotates smoothly.

Rotate the shaft by hand. Make sure there is no rubbing that
can lead to excess heat generation or sparks.

Re-check the alignment to make sure that
pipe strain has not caused any misalign-
ment.

If pipe strain exists, then correct the piping.

4.5 Piping checklists

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

Summary of Contents for GOULDS PUMPS 3296 EZMAG





































































































Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands

ITT GOULDS PUMPS 3296 EZMAG, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for GOULDS PUMPS 3296 EZMAG

Reviews:

Related manuals for GOULDS PUMPS 3296 EZMAG

Brands by name

Popular brands