ITOX G4M300-M12 User Manual Download Page 76

Page: 76 / 114

BIOS Setup

Onboard Device

Move the cursor to this field and press <Enter>. The following
screen will appear.

The settings on the screen are for reference only. Your version may not be identical
to this one.

USB Controller

This field is used to enable or disable the USB ports.

USB 2.0 Controller

If you are using USB 2.0, this field must be set to Enabled.

USB Keyboard Support

If you are using a USB keyboard under DOS, set this field to
Enabled.

IDE HDD Block Mode

Enabled

The IDE HDD uses the block mode. The system BIOS
will check the hard disk drive for the maximum block
size the system can transfer. The block size will depend
on the type of hard disk drive.

Disabled

The IDE HDD uses the standard mode.

Summary of Contents for G4M300-M12



















































































































Search results

Summary of Contents for G4M300-M12

Reviews:

Related manuals for G4M300-M12

Brands by name

Popular brands

ITOX G4M300-M12, User Manual

Search results

Summary of Contents for G4M300-M12

Reviews:

Related manuals for G4M300-M12

Brands by name

Popular brands