ITOX G4M300-M12 User Manual Download

Page: 69 / 114

BIOS Setup

Security Option

This field determines when the system will prompt for the password
- everytime the system boots or only when you enter the BIOS
setup. Set the password in the Set Supervisor/User Password
submenu.

System

The system will not boot and access to Setup will be
denied unless the correct password is entered at the
prompt.

Setup

The system will boot, but access to Setup will be denied
unless the correct password is entered at the prompt.

APIC Mode

Leave this field in its default setting.

OS Select for DRAM > 64MB

This field allows you to access the memory that is over 64MB in
OS/2. The options are: Non-OS2 and OS2.

Small Logo(EPA) Show

Enabled

The EPA logo will appear during system boot-up.

Disabled

The EPA logo will not appear during system boot-up.

Summary of Contents for G4M300-M12



















































































































Search results

Summary of Contents for G4M300-M12

Reviews:

Related manuals for G4M300-M12

Brands by name

Popular brands

ITOX G4M300-M12, User Manual

Search results

Summary of Contents for G4M300-M12

Reviews:

Related manuals for G4M300-M12

Brands by name

Popular brands