iSystem IC57163 User Manual Download Page 3 | Manualshive

Page: 3 / 24

iSystem IC57163 User Manual Download Page 3

Contents

Infineon DAP/DAPE Active Probe

Important safety notice ......................................................................................................................... 5

Package content ...................................................................................................................................... 6

Specifications ........................................................................................................................................... 7

Operation ................................................................................................................................................... 8

Device description .............................................................................................................................................................................................................. 9
Recommended Target Debug Connectors and Position ...................................................................................................................... 10
ECU14 DAP 10-pin 1.27mm Converter ............................................................................................................................................................. 11
MEDC17 DAP 10-pin 1.27mm Converter ......................................................................................................................................................... 12
ERF8 DAP 22-pin Converter .................................................................................................................................................................................... 13

Active Probe and the iC5700 Connecting Guidelines .................................................................... 14

Connecting Active Probe to the Target ............................................................................................................................................................ 15
Setting Debug Interface Voltage Levels ......................................................................................................................................................... 17
DAP and DAPE configuration .................................................................................................................................................................................. 18

Further Active Probe Settings ............................................................................................................ 19

Accessories ............................................................................................................................................. 21

User Notes .............................................................................................................................................. 22

«
1
2
3
4
5
...
»

Summary of Contents for IC57163

























Reviews:

No comments