IST Proline IF-O Owner'S Manual Download Page 2

Thank you for choosing IST IF-O Inflator-Octo

1. IMPORTANT WARNINGS

WARNING

THIS MANUAL MUST BE READ AND UNDERSTOOD ENTIRELY BEFORE USING

THE PRODUCT. IT IS ADVISED THAT YOU KEEP THIS MANUAL IN YOUR

POSSESSION DURING THE ENTIRE LIFE OF YOUR IF-O.

When diving, you must follow the rules and apply the skills taught by a recognized

scuba diving certification agency. Before taking part in any diving activity, it is mandatory

to have successfully completed a scuba diving course covering both theoretical and

technical aspects of diving.

Do not push down on the purge button in low temperatures, as this may cause a second

stage freeze-up.

Max Intermediate Pressure is 1.103 kPa (155 psi).

Using the IF-O with first stages exceeding this intermediate pressure may cause air

leakage from the mouthpiece and inflation of the buoyancy vest.

2. CE CERTIFICATION

IF-O has successfully passed the certification tests required by

EN250:2014 to an auxiliary emergency breathing device integrated

with a buoyancy inflator system.

The use of IF-O as regulator is certified exclusively for diving in water temperature higher

than 10ºC(50ºF),as indicated by the markings on the unit.

Do not use the IF-O as a regulator while diving in water temperature

below that limit.

Failure to follow this instruction could lead to serious injury or death.

IST

WARNING

WARNING

WARNING

WARNING

1

Summary of Contents for IF-O

















Reviews: