Isotra SCREEN HR7, screen HR8-ZIP Measurement And Assembly Manual Download

Page: 23 / 23

MEASUREMENT AND ASSEMBLY MANUAL

Validity of the manual: 1. 6. 2017

•

Remove the fabric roll from the retainer.

•

Remove the bottom slat from the guide rails (see illustration).

•

Detach the zipper and fabric from the sliding blocks.

•

Pull the bottom slat off of the fabric.

•

Unroll the fabric from the fabric roll.

•

Pull the fabric off of the fabric roll.

•

Take the new fabric.

•

Pull the fabric onto the fabric roll.

•

Roll the fabric around the fabric roll.

•

Pull the bottom slat onto the fabric.

•

Attach the zipper and fabric to the sliding blocks.

•

Twist the bottom slat into the guide rail; make sure the zipper enters the U-shaped part of the plastic guide profile

correctly.

•

Place the fabric roll in the retainer.

•

Reattach the cover.

•

Lower the screen and test whether everything works properly.

fig. 38

Summary of Contents for SCREEN HR7, screen HR8-ZIP
























Search results

Summary of Contents for SCREEN HR7, screen HR8-ZIP

Reviews:

Related manuals for SCREEN HR7, screen HR8-ZIP

Brands by name

Popular brands

Isotra SCREEN HR7, screen HR8-ZIP, Measurement And Assembly Manual

Search results

Summary of Contents for SCREEN HR7, screen HR8-ZIP

Reviews:

Related manuals for SCREEN HR7, screen HR8-ZIP

Brands by name

Popular brands