21
252_EN_IS_1_3_00.doc
FUNCTION FOR OUTPUT 1, 2,3
q
OFF: DISABLED
q
PLS: PULSE FOR POSITIVE AND NEGATIVE FLOW RATE
q
PLS-: PULSE FOR NEGATIVE FLOW RATE
q
PLS+: PULSE FOR POSITIVE FLOW RATE
q
EXT. COMM.: ONLY AVAILABLE WITH DATA LOGGER MODULE
q
HARDW AL: CUMULATIVE ALARM OUT interrupt coils, empty pipe, meas. error (ENERG. = NO ALARMS)
q
OVERFLOW.: OUT OF RANGE ALARM OUTPUT (ENERGISED = FLOW RATE OK)
q
EMPTY PIPE: EMPTY PIPE ALARM OUTPUT (ENERGISED = FULL PIPE)
q
MAX+MIN±: MAX AND MIN FLOW RATE ALARM OUTPUT (ENERGISED = AL. OFF)
q
MIN AL±: MIN DIRECT/REVERSE FLOW RATE OUTPUT(ENERGISED = AL. OFF)
q
MIN AL-: MIN REVERSE FLOW RATE OUTPUT(ENERGISED = AL. OFF)
q
MIN AL+: MIN DIRECT FLOW RATE OUTPUT(ENERGISED = AL. OFF)
q
MAX AL: MAX DIRECT/REVERSE FLOW RATE OUTPUT(ENERGISED = AL. OFF)
q
MAX AL-: MAX REVERSE FLOW RATE OUTPUT (ENERGISED = AL. OFF)
q
MAX AL+: MAX DIRECT FLOW RATE OUTPUT ( ENERGISED = AL. OFF)
q
RANGE: RANGE INDICATION OUTPUT (ENERGISED = SCALE 2)
q
SIGN: FLOW DIRECTION OUTPUT (ENERGISED = -)
again. Allowed values for this parameter: ON / OFF.
N.B.:
the autorange doesn’t allow using the
manual change of range (see pos. 5.8)
(POS. 3.5) Energy saving enable
[E.SAVING=ON/OFF]
Enable automatic energy saving function. This function IF ON, ENABLES THE OPERATION OF THE
METER IN ACCORDANCE WITH INTERVALS OF FIXED TIME WITH THE FOLLOWING FUNCTION; if
OFF the measure is continuous at 10 Hz of frequency. Allowed values for this parameter: ON/OFF
MENU 6. OUTPUT
(POS. 6.1-6.2) Function corresponding to on/off output 1-2
[OUT 1-2=XXXXXX]
Choice of the function corresponding to digital Output 1-2. The functions are listed in the table
below
MENU 8.DISPLAY
(POS. 8.2-8.3-8.4-8.5) Reset totalizer
[T/P+/- RESET=ON/OFF]
Reset of totalizer by key board;
N.B.:
The reset of the totaliz . may be done from the function listed upon pushing the key
and the key . The reset of partial totalizer /currency may be done also from the visualization
pages at page 12 like this . Push the key . Set the L2 CODE if request and then push the
key . At the question “RESET TOTALIZ.?”. Push the key to proceed with the zeroing.
Push any other key to cancel this operation.
(POS. 8.9) Enable conversion currency
[CURRENCY =ON/OFF]
This function visualizes the values of the partial totalizators converts in the unite of selected
currency.
(POS. 8.10) Decimal currency
[CURR DECIM =X]
This function allows the choice of the numbers of decimals to use for the visualization of the
numerical value converted in the currency. The allows values are from 0 to 3. The function is active
only if the currency function is enable
(POS. 8.11-8.12) Conversion factor for flow rate totalizers
[EUR/dm
³+
=X]
Set the value of conversion/currency for totalizers. There are three fields for this parameter, from
left to right:1) monetary token, 2 ) default/personalized monetary token, 3 ) conversion coefficient.
For the selection setting the cursor over the field to modify. The mode set of monetary token could
be two:
•
choice of one of the 7 predetermined monetary tokens (standard ISO 4217-REV81):
EUR = Eur, USD = USA dollar, CAD = Canadian dollar, AUD = Australian dollar, GPB = English
pound, CHF = Swissfranc, JPY = Japanese yen.
