Isolite E3MINI Series Installation & Operation Manual Download Page 4

 

 

2.0  RECEIVING AND STORAGE 

 

2.1   Inspection 

     The E3MINI Series central inverter and batteries are shipped together. Upon 
arrival, please inspect the contents to ensure that no shipping damage has 
occurred. This is especially important with the batteries 

 ensure that there are no 

cracks or leaks. If any damage has occurred, notify the shipping carrier immediately 
and submit a damage claim. 
 

WARNING

 - Do not use system with a damaged battery as this may cause an unsafe 

condition. 

 

2.2   Storage

 

     Storage before the installation is critical for the battery life expectancy and 
warranty. Store the system indoors in a clean, dry and cool location. Storage at 
higher temperatures will result in accelerated rates of self-discharge and possible 
deterioration of battery performance and life. 

 

 

 

     

Storage at high temperatures will result in accelerated rates of self-discharge and 
possible deterioration of battery performance and life. Storage times exceeding the 
above may result in plate sulfation, which may adversely affect electrical 
performance and expected life. 

 

Failure to install and charge the batteries as noted 

VOIDS the battery’s warranty

 

 

DANGER

 

-

 

Batteries present a risk of electrical shock and high short circuit current. 

Do not smoke, cause a flame or spark in the immediate are of the batteries. Use 
proper lifting means when moving batteries and wear all appropriate safety 
clothing and equipment. 
 

 

4

   |    INSTALLATION / OPERATION MANUAL 

WARNING

  

 

The maximum storage time from shipment to initial 

charge is 6 months

 for batteries stored at ambient temperatures no 

warmer than 77°F (25°C). For storage temperatures greater than 77°F 
(25°C) the batteries must be recharged one (1) month sooner for every 
5°F (3°C) increase above 77°F (25°C). 

 

Summary of Contents for E3MINI Series

































Reviews: