Isolite E3MINI Series Installation & Operation Manual Download Page 19

 

 

10.0  WARRANTY 

     There are two separate warranty periods for the E3MINI Series Central Inverter 
System. The Electronics/Cabinet warranty period is for 3 years from the date of 
shipment.  It is warranted against defects in workmanship and materials under normal 
and proper use. 
The batteries are covered under a separate warranty and these durations may change 
dependent on battery type. 
 
 
 
 

10.1   Technical Service and Support 

     Our technical support staff is available before, during, and after the installation for 
help on any detail of this product. Should you need help, please contact our service 
center at: 
 

Service Center  

1-800-967-5573 

 
     We are available during normal business hours Eastern Standard Time Zone. 

 

10.2   Return Material Authorization (RMA) 

     At no time will material be accepted as returned goods without a RMA number issued 
from the factory. If parts are deemed defective by our Technical Service group and are 
troubleshot at the site to be defective they can be exchanged at no cost during the 
warranty period with an RMA. 
     When returning defective parts back to the factory, the RMA number must be written 
on the packaging, bill of lading, or shipping labels so it can be properly identified. 
     Technical Service will make every effort to troubleshoot the problem over the phone 
before an RMA will be issued. Phone troubleshooting may save both the customer and 
manufacturer added time and expense. Cooperation is greatly appreciated. 
 
 
 
 

 

E3MINI SERIES   |   

19

 

BATTERY TYPE 

 

WARRANTY DURATION 

Standard VRLA 

 

1 year full, 9 years pro-rata 

 

Summary of Contents for E3MINI Series

































Reviews: