manualshive.com logo in svg

ISGM i-2UVA, User Manual, Page: 29 / 40

Share
Download
ISGM i-2UVA User Manual Download Page 29

29

Product Version 1.0 | Revision A | Released 2022-2-21

LED ENGINE

The i-2 UVA LED engine is comprised of 365nm wavelength ultra-violet LEDs. Extra care should be taken to avoid pro

-

longed contact with UV light. Please refer to safety warnings at the beginning of this manual.

INDIVIDUAL FIXTURE SETTINGS 

Setting the dimming curve

Setting the dimming curve will determine the fixture’s behaviour, when changing the light intensity between 0% - 
100%.
Linear control provides uniform adjustment throughout the control action, whereas gamma corrected dimming pro

-

vides finer control at low light levels, where the eye is more sensitive to change. By default, the i-2 UVA uses gamma 
corrected dimming. For a uniform response, set all fixtures to the same dimming curve.

Flipping the OLED display (POI n.a.)

If the fixture is installed hanging upside down, it might be useful to flip the display so that it is easier to read.
To flip the display, press ENTER and select SETTINGS → FLIP DISPLAY, or press the up and down buttons on the control 
panel at the same time.

Setting the OLED display saver (POI n.a.)

By default the OLED display dims down after a short period when the control panel is not in use. The display can also 
be set to turn off completely. Pressing any key will turn on the display or restore it to normal brightness. 
To configure the display settings, press ENTER → SETTINGS → DISPLAY SAVER.

PLEASE NOTE! TO AVOID THE RISK OF DISPLAY DETERIORATION CAUSED BY LONG TERM USAGE, IT IS RECOM-
MENDED TO SELECT SETTINGS → DISPLAY OFF.

Setting the fan mode

For environments where low-noise is a requirement, or where the fixture will be operating in high temperatures, it is 
possible to adjust the default fan speed by going to SETTINGS → FAN MODE in the menu. In POI versions, this is done 
via RDM.

PLEASE NOTE! IN POI FIXTURES, FAN MODE ADJUSTMENT IS DONE THROUGH RDM.

FIXTURE PROPERTIES

FACTORY DEFAULT 

• 

When restoring the i-2 UVA to the factory defaults, 
the following settings will be set:

• 

DMX address = 1.

• 

DMX mode = Default mode (6 channel).

• 

Startup mode = DMX.

• 

Display saver = Off.

• 

Flip screen = Off.

• 

RDM device label set to = Fixture type name.

• 

Internal program reset.

Summary of Contents for i-2UVA









































Reviews:

No comments