manualshive.com logo in svg

Isee IGEP v2, Hardware Reference Manual

Share
Download
Isee IGEP v2 Hardware Reference Manual Download Page 9

 
 
IGEP

TM 

v2 

Hardware Reference Manual

 

 

 

ISEE 2007 S.L.  All rights reserved, IGEP

™

 is a registered trademar k from ISEE 2007 S.L. The followi ng is provided for informational purpos es onl y.  

DOCUMENT FROM ISEE 2007 S.L.   Ref: MAN-PR-IGEP0020-RCx 

9 

Feature 

Specifications 

RAM Memory 

512 MBytes LPDDR SDRAM 

–

 200 Mhz

 

Storage 

NAND Flash 512 Mbytes  

On board micro-SD socket  

Table 3 Memory and Storage 

 

Feature 

Specifications 

Debug 

Console RS232 + JTAG Interface 

Indicators 

2 Bicolor USER LEDS 

USB 2.0 LS/FS/HS OTG  

1 Mini AB USB socket connector (dual slave and host role) 

USB 2.0 HS HOST 

1 Type A USB socket connector (standard USB host)  

Audio stereo in/out 

3.5mm standard stereo audio jack  

microSD 

microSD connector (SD and SDHC cards supported) 

DVI video output 

DVI-D  using  HDMI  connector.  (video  and  TS  lines  are  available  in 
expansion connector also). 

Ethernet 

10/100 MB BaseT (RJ45 connector with led link/activity) 

Expansion connector 

Power  5V  and  1.8V,  UART,  McBSP,  McSPI,  I2C,  GPIO,  RS485  with 
transceiver, Keyboard. 

Table 4 On-board connectors and devices 

 

Feature 

Specifications 

Wifi 

IEEE 802.11b/g 2,4GHz 

Bluetooth 

2.0 

Antenna WiFi/Bluetooth 

1  shared  internal  antenna  (integrated  on  PCB),  optional  external 
antenna. 1 x HIROSE UL connector  

Table 5 Wireless connectivity 

 

Summary of Contents for IGEP v2



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands