GB
3
Safety regulations:
Please read these directions for use carefully
and observe the information provided. It is impor-
tant to consult these instructions in order to
acquaint yourself with the unit, its proper use and
safety regulations.
Suitable measures must be taken to keep the
unit out of children’s reach.
The pressure sprayer is designed for spraying
common home and garden solutions. This is pri-
marily meant to include pesticides, weed killers
and liquid fertilizers.
The pressure sprayer is not designed to spray
acidic and caustic liquids. Nor should it be used
to spray impregnating agents.
Only use a suitable nozzle wire or cleaning agent
to clean clogged nozzles.
Do not spray contents of sprayer on persons or
animals.
Always wear protective clothing when spraying
pesticides and insecticides.
Ensure that liquid sprays are not heated beyond
the permitted operating temperature of 40 °C.
When mixing and working with spray solutions,
always follow the manufacturer’s instructions.
Each time the spraying unit has not been used
for an extended period of time it should be
checked for possible damage prior to reusing it.
Immediately replace defective parts.
Use only original replacement parts.
Do not leave the unit (filled or empty) in direct
sunlight.
Before placing the unit in winter storage,
thoroughly clean and dry it out so that it is not
damaged by freezing temperatures.
We will not be liable for any damage that results
from improper repairs and/or improper handling
of the unit (e.g. using the unit in ways for which it
was not intended).
Opening the unit or performing maintenance
work on it is only permitted when the tank is
depressurized.
To relieve the pressure, pull up the funnel-sha-
ped knob connected to the safety valve.
Only use currently approved pesticides.
Please observe COSHH Material Safety Data
Sheets.
Pesticides include - but are not limited to - herbi-
cides, insecticides, fungicides and growth regula-
tors as well as materials that are intended to be
used in conjunction with these agents in order to
modify their properties or effects.
Each time after using the unit and prior to perfor-
ming any maintenance work on the unit, always
relieve the pressure via the overpressure valve
by raising the overpressure valve.
Technical data
Max. filling capacity
5 l
Total filling capacity
7 l
Volumetric flow rate, Vmax =
1.07 litres/min.
Permissible operating pressure
3 bar
Permissible operating temperature
+ 40°C
Safety valve / vent valve
1
Nozzle
hollow cone 1 mm
Nozzle spraying angle
max. 60°
Repulsion angle at the nozzle
less than 5N
Assembly
Screw the spray tube (Fig. 1/Item 1) to the pistol
grip (Fig. 1/Item 2)).
Do not unscrew the overpressure valve ( Fig.
3/Item 6)!
Check to ensure that the screw connections for
the hose at the spray gun handle and on the tank
are tight!
Starting up and venting
Unscrew the feed funnel from the bottom of the
pressure sprayer (Fig. 2/Item 5).
Before you screw out the pump, raise the over-
pressure valve (Figure 3/Item 6) and let off any
overpressure that may be in the unit.
Press down the pump handle as far it will go and
slowly unscrew the pump (counter-clockwise).
Screw the feed funnel onto the tank (Fig. 3/Item
5).
Fill the container up to no further than the 5 liter
mark with the preparation you want to spray.
Follow the instructions issued by the producer of
the preparation you are using.
Remove the feed funnel from the tank.
Insert the pump, press down the pump handle as
far it will go and screw in the pump (clockwise)
until it is tight again. The pump handle latches
simultaneously into the bayonet lock.
Anleitung GLDS 5 GB 16.12.2004 9:57 Uhr Seite 3
