IRT-6630-DTR
I.R.T. Communications Pty Ltd | www.irtcommunications.com
Page 7 of 22
Revision 01
TECHNICAL SPECIFICATIONS
Transmitter:
Input serial data signal
2.97 Gb/s (3G-SDI) to SMPTE 424M;
1.485 Gb/s (HD-SDI) to SMPTE 292M;
270 Mb/s (SD-SDI) to SMPTE 259M-C and DVB-ASI.
Input impedance
75 Ω.
Input return loss
> 15 dB 5 MHz to 1.5 GHz;
> 10 dB 1.5 GHz to 2.97 GHz.
Automatic cable compensation
> 100 m at 2.97 Gb/s (3G-SDI) with Belden 1694A (typ. 110m);
> 100 m at 1.485 Gb/s (HD-SDI) with Belden 1694A (typ. 160m);
> 250 m at 270 Mb/s (SD-SDI/ASI) with Belden 8281 (typ. >300m).
Input connector
2 x BNC on rear panel, with I/P 1 taking priority & I/P 2 automatically switching in
on loss of I/P 1.
Output connector
1 x BNC (OUT 1) on rear panel, link selectable Tx input monitor, or nil if set as a
second Rx output.
Receiver:
Number of outputs
2 data reclocked,
AC coupled.
Output level
800 mV ± 10%.
Output impedance
75 Ω.
Output return loss
> 15 dB 5 MHz to 1.5 GHz;
> 10 dB 1.5 GHz to 2.97 GHz.
Output rise and fall time
< 135 ps at 2.97 Gb/s and 1.485 Gb/s;
> 0.4 ns and < 1.5 ns at 270 Mb/s.
Intrinsic jitter
< 0.3 UI at 2.97 Gb/s reclocked;
< 0.2 UI at 1.485 Gb/s reclocked;
< 0.1 UI at 270 Mb/s reclocked.
Output connector
2 x BNC on rear assembly, or 1 x BNC if OUT 1 has been link selected as an input
monitor.
Optical:
Optical output
0 dBm +4.5/-0 dB CWDM DFB laser.
Optical input
APD detector, -9 to -27 dBm input level at 3G-SDI, typically < -30 dBm at HD/SD-SDI.
Available wavelengths
1310nm or 1550nm. Other wavelengths available upon request.
Optical path loss
4, 5
9 to 27 dB at 3G-SDI, typically >30 dB at HD/SD-SDI, APD detector.
(Optical path loss = Laser O/P power – Detector I/P power)
Optical fibre
Designed for use with 9/125 μm single mode fibre.
Optical connector
2 x LC/PC (standard) on rear – direct connection to main card, 1 Tx and 1 Rx;
1 x SC/PC (standard) with WDM option fitted.
Power Requirements:
Voltage
+ 12 Vdc.
Power consumption
< 5 VA.
Other:
Temperature range
0 - 50° C ambient.
Mechanical
Suitable for mounting in an openGear® 2RU rack chassis.
Dimensions
(openGear® standard)
33.6 mm x 2U x 325 mm.
Supplied accessories
Rear connector assembly.
Ordering
IRT-6630-DTR
IRT-6630-DTR, programmed with DashBoard™ control.
WDM order codes
IRT-6630-DTR/1310/WDM & IRT-6630-DTR/1550/WDM.
NOTE:
4
Typical values based using DFB laser. Optical attenuator supplied for when optical
path loss is less than 9dB for APD detector.
5
With WDM option fitted for combined use on a single fibre, optical path loss is
reduced by approximately 2dB.
6
With WDM module fitted, when operating as a pair, one IRT-6630-DTR must be
fitted with a 1310nm laser and the other a 1550nm laser.
Due to our policy of continuing development, these specifications are subject to change without notice.
