IRT DVA-3009 Instruction Manual Download Page 4

3009-dva.ib.doc 

Page 4 of 8 

06.05.2003

Technical specifications 

 

DVA-3009

 

Input: 

Number 2. 
Impedance 75 

Ohm. 

Return loss 

>20 dB 5 MHz to 360 MHz. 

Equalisation 

Automatic, better than 300 metres at 270 Mb/s 
for Belden 8281 or equivalent cable. 

 

(reduces to approx. 200m when LK3 (input 
A), LK4 (input B) is closed). 

 

Outputs: 

Number 

3 ASI/SDI per input. 

Signal level 

800 mV ± 10% 

Impedance 75 

Ohm. 

Return loss 

>20 dB 5 MHz to 360 MHz. 

DC offset 

Nil. 

 

Performance: 

Cable compensation 

Automatic, better than 300 metres at 270 Mb/s 
for Belden 8281 or equivalent cable. 
(reduces to approx. 200m when LK3 (input 
A), LK4 (input B) is closed). 

Output rise time 

<1 ns, (700 ps typically). 

 

Alarms:

 

Signal Loss on either channel 

Contact closure. Link selectable N.O./N.C. 

or power failure 
 

Connectors:

 BNC. 

 

Indicators: 

Power 

LED (green) for +5 Vdc. 

Signal present 

LED (green) when signal present for each input. 

 

Power requirement: 

Voltage 

28 Vac CT (14-0-14) or 

±

16 Vdc 

Consumption 

2.5 VA (<80 mA). 

 

General: 

Temperature range 

0 - 50° C ambient 

Mechanical 

Suitable for mounting in IRT 19" rack chassis with input, output and 
power connections on the rear panel. 

Dimensions 

6 HP x 3U Extended Eurocard (220 mm x 100 mm). 

Weight 

With rear assembly 365g. 

Finish:  

Front panel 

Grey, with black lettering & red IRT logo 

 

Rear 

assembly 

Detachable silk-screened PCB with direct mount connectors to 
Eurocard and external signals 

 
Supplied accessories 

Rear connector assembly with matching connector for alarm outputs. 

 
 

Due to our policy of continuing development, these specifications are subject to change without notice.  

 

Summary of Contents for DVA-3009










Reviews: