manualshive.com logo in svg

Ironman4x4 SS075, Installation Manual

Share
Download
Ironman4x4 SS075 Installation Manual Download Page 1

RAID SIDE STEPS TO SUIT RAM DS

INSTALLATION

GUIDE

• Ironman 4x4 SS075 Side Steps to suit Ram DS. 
• It will take approximately 1.5 hours to install.
• Read instructions fully before commencing fitment. Check hardware kit contents against   

   content list below. Do not use this product for any vehicle make or model, other than 

   specified in these instructions. 
• Do not remove labels from this Raid product. It is good practice to record the batch  

   number on the customer’s job card for future reference.

IMPORTANT:

 Raid Accessory installations should only be done by a qualified person,  

and it is the responsibility of this person to ensure correct fitment. 

WARNING: This product has been tested for side air bag compatibility and therefore 

the mounting system MUST NOT be modified. The operations of the side air bags are 

not affected if installation is followed in accordance to these instructions.

 SS075/030522

SS075

©Copyright 2022 Ironman 4x4 Pty Ltd. No part of this publication may be reproduced or replicated without the prior written consent of Ironman 4x4 Pty Ltd

Summary of Contents for SS075









Reviews:

No comments

Brands by name

Popular brands

Load more brands