background image

     5.  MOUNTING AND CONNECTION

The device should be mounted on a flat surface in the location allowing unobstructed access 
with cards.
To mount the device using mounting kit, 

perform

 the following steps:

1. Un

screw

 the mounting screw and 

remove

 the top device casing lid.

2. Mark and drill two 6 mm holes, each 30 mm deep, in the wall (or other flat surface). Put in the 
  wall plugs.
3. Connect both cables in accordance with electrical layout. Insulate all wires at the junction  
  points.
4. Connect the device to 

power supply

 and check its operation.

5. Lead both cables, so that they are not jammed when mounting the device. Fix the device  
  base in position with mounting screws.
6. Put the top casing lid or the pocket accessory in place, and fix it with a screw.

      6.  PROGRAMMING

6.1  Select Operation Mode

To select an operation mode, touch the device with a Master card no longer than 5 s. Each touch 
cycles through the modes: Switch, Energy Pocket, and Timed.

6.2  Select Programming Mode

Touch and hold a Master card to the device. After ~5 s the LED 

starts

 blinking green, indicating the 

Add Access Card Mode. Continue to hold the card to the device, and after another 5 s the LED 
changes into blinking red, indicating the Erase All Cards Mode. After another 5 s of holding the card, 
the LED changes into blinking yellow, indicating Release Timer Setup Mode. In further 5 s the 
blinking stops and the device returns to its normal operation, the LED will become solid and its 
colour will indicate one of the three Operation Modes selected in paragraph 6.1
Holding the Master card further will repeat the cycle through the programming modes described 
above: Blinking green, Blinking red, Blinking yellow, solid.

To  select  a  programming  mode,  take  the  Master  card  away  when  the  LED  shows  the  colour 
corresponding to the desired programming mode.

6.3  Adding Access Cards

While the LED is blinking green, please take away the Master card from the reader. The LED starts 

to blink twice faster, indicating that Add Access Cards Mode is chosen.

Start touching the device with the cards to add as Access cards. When a card is added, the LED will 

show steady red shortly. If this won't happen, either the card is already present in the database, or is 
of an incompatible standard. 
Device will revert to normal operation either automatically   in 20 s after the last card touch, or 
immediately after a Master card touch.

6.4  Erase All Cards

While the LED is blinking red, please take away the Master card from the reader. The LED starts to 
blink twice as often, indicating that Erase All Cards Mode is chosen. It will now wait 20 s for another 
Master card touch. If none followed within 20 s, the mode will end and the keys database erase will 
be cancelled.

page 

3

MATRIX

 

III 220

www.ironlogic.

me

Summary of Contents for Matrix III 220







Reviews: