IQ Vertiq 2306 Instruction Manual Download Page 14

Page: 14 / 17

Vertiq 2306

3 <Beep 3>

4 <Beep 4>

5 <Beep 5>

7 <Spin direction CCW>

8 <Spin direction CW>

9 <3D mode off>

10 <3D mode on>

12 <Save direction and 3D mode>

For example, if you want to change Motor 3 to CW 3D, type the following in the CLI:

dshotprog 2 8

dshotprog 2 10

After changing the spin direction or the 3D mode, you must save the changes

Continuing the above example on Motor 3, type:

dshotprog 2 12

Pre-Made Application Settings

These pre-made settings were designed to give users maximum performance in their specific application

Settings Description: Speed Module

–

speed factory default - factory default, unconfigured

–

APC6x4 - standard 2D drones using APC6x4 props, velocity (closed-loop) mode

–

APC6x3R - reversible 3D drone using APC6x3R props, velocity mode

V1.1

2021 IQinetics Technologies Inc.

14/17

PRE-MADE APPLICATION SETTINGS

Summary of Contents for Vertiq 2306


















Search results

Summary of Contents for Vertiq 2306

Reviews:

Related manuals for Vertiq 2306

Brands by name

Popular brands

IQ Vertiq 2306, Instruction Manual

Search results

Summary of Contents for Vertiq 2306

Reviews:

Related manuals for Vertiq 2306

Brands by name

Popular brands