manualshive.com logo in svg

IPSO WE 110, Instruction Manual

Share
Download
IPSO WE 110 Instruction Manual Download Page 18

18

Special functions

By keeping the program select button (SELECT) pressed and then pressing the

START/STOP button at the same time, it is possible to use special functions.

After a while, the left decimal point starts to flash. (A)

This means that the program will keep repeating the segment that is now

active (Time stop).

To continue the program normally, press the START/STOP button. Or

if you want to select the following function, press the program select

button (SELECT) once again.
The middle decimal point lights up and the left keeps flashing (B). Now

the time will be stopped and the water will be heated to 40°C with reduced

wash action and high water level. By means of this soak program you can

prolongue the pre-wash in case of very dirty linen.

To continue the program normally, press the START/STOP button. Or

if you want to select the following special function, press the program

select button (SELECT) once again.

The right decimal point now lights up (C).

This means that all wash actions are being executed at reduced wash

action.

To continue the program normally, press the START/STOP button. Or

if you want to select the following special function, press the program

select button (SELECT) once again.
The right decimal point lights up and the left flashes.

Now the program activates a “time stop” during the wash cycle but in

this case with a reduced wash action.

To continue the program normally, press the START/STOP button.

Test program

By keeping the program select button (SELECT) pressed, when selecting the

program, for more than 5 seconds, you enter the “

test program

” (0). This was

specially designed to help the technical service in case of malfunction.

Thermo-magnetic motor protection

When the thermo-magnetic motor protection is activated, the red control pilot

light on the fascia panel will light up and the display will turn off. When the

protection (manually or automatically) is being reset, a flashing “ S “ will appear

on the display. This means that you should select again the program.

p

p

p

p

Summary of Contents for WE 110

























Reviews:

No comments

Brands by name

Popular brands

Load more brands