BMA_77024-o16m-05_Rev2_en
IPAS GmbH, Hölscherstraße 27, D-47167 Duisburg
OUTPUT SCHEMATIC
Each channel can be configured to be used as 2 binary outputs or as
one blind channel. In case Fan Coil controller is selected, 4 outputs will
be used. Each output can be powered by an independent phase.
ANNEX 1: Manual Control
Attention:
This option is activated after ETS Download. In delivery
status this option is not available.
The Power Block actuator has 2 push buttons and 2 status LEDs for
each channel on the front side. These buttons can be activated to
control each and every channel/output individually if you select “yes” in
the relevant parameter options in Binary outputs / Shutter/Blinds / Fan
Coil. The LEDs are arranged in two rows, whereas the LEDs
represent:
For Binary outputs
The top row: channels A1,A2,B1,B2,C1,C2,D1,D2
The bottom row: channels E1,E2,F1,F2,G1 G2,H1,H2
For Shutter/blinds:
The top row: channel's first relay A1->UP,
A2->DOWN, B1-UP, etc.
The bottom row: channel's second relay C1->UP,
C2-> DOWN, D1-> UP, etc.
For Fan Coil:
The top row:
-
FC1: Fan Speed = Fan 1 (A1),
Fan 2 (A2), Fan 3 (B1) // Output valve = B2.
-
FC2: Fan Speed = Fan 1 (C1),
Fan 2 (C2), Fan 3 (D1) // Output valve = D2.
The bottom row:
-
FC1: Fan Speed = Fan 1 (E1),
Fan 2 (E2), Fan 3 (F1) // Output valve = F2.
-
FC2: Fan Speed = Fan 1 (G1),
Fan 2 (G2), Fan 3 (H1) // Output valve = H2.
MANUAL CONTROL – PARAMETER
The Parameter Mode allows you to control all the channels of the
actuator as configured in the ETS. The Action simulates a telegram
received at the switching object of the selected channel.
BINÄRY
SHUTTER/BLIND
Press action: Sends Toggle
ON/OFF command “0/1” to the
“Switching” object.
.
LED = ON (indicates
channel status)
LED = OFF (indicates
channel status)
Long press action (Channel
output 1):
Sends a UP command “0” to the
“Move” object.
Long press action (Channel
output 2):
Sends a DOWN command “1” to
the “Move” object.
Short press action (any output)
(while shutter/blind is moving) of
same button:
Sends a Stop command to the
“Stop…” object.
LED blinks while moving
UP/DOWN during parameterized
time.
Fan Coil
Valve press action:
Sends toggle ON/OFF command to the relay (ON
= Contact closed / OFF = Contact open)
Fan speed press action:
Actives the selected Fan Speed switching the
corresponding relays, depending of the configuration Fan Coil Type
(Single or Multiple)
Type of Fan Coil = Single (Only one output can be ON at time)
o
LED = ON (indicates the actual Fan Speed active)
o
LED = OFF (indicates the actual Fan Speed is not active)
Type of Fan Coil = Multiple (Switch outputs sequentially ON)
o
LED = ON (Accumulated ON status, it indicates the actual
Fan Speed active)
o
LED = OFF (indicates the actual Fan Speed is not active)
MANUAL CONTROL – TEST
The Test Mode allows you to test all the loads/wiring connected to the
channels. It is independent from the ETS configuration of the actuator
(since the “Manual Control / Param mode + Test mode” is a default
option, you can use the Test mode even before programming the
actuator).
Important note: Should a blind/shutter be connected to a channel, the
2 channels may never be closed at the same time. Therefore, even in
Test mode, if the channel is configured as a blind, this safety measure
is implemented. For this reason, it is better to first commission the
OUTPUT: CHANNEL TYPE SELECTION before using the Test mode.
To change into the test mode, any button can be used depending of
the channel configuration:
- If “Binary” or” Fan Coil” channel is configured: Press any button for
at least 500ms
- If “Blind” channel is configured: Press the two buttons of any channel
at the same time for at least 500ms
To change back to the normal “Parameter Mode” the same procedure
should be repeated. Be aware by changing back to “Parameter Mode”
the device will restart. Also after the device has restarted and if the
channel is configured to be a blind channel, it will do a calibration
movement on the first movement command.
In order to indicate that the actuator is in Manual Control / Test
Mode, the LED of the selected channel is continuously making a short
blinking action every second; no matter whether the channel is ON
(LED ON) or OFF (LED OFF).
