IOGear MiniView GCS1772 User Manual Download Page 32 | Manualshive

Page: 32 / 45

background image

30

Shut down the computers on your MiniView™
installation and make sure you have set the KVM in
firmware upgrade mode as instructed under section
Hotkey operation

→

→

→

→

→

Firmware upgrade mode

Make sure the power is plugged into the KVM.

Once the power is plugged in and the switch is set
to upgrade, all of the amber lights on the KVM will
flash once per second. Now you are ready to run
the firmware upgrade utility.

4.

5.

The Firmware Upgrade Utility

«
...
30
31
32
33
34
...
»

Summary of Contents for MiniView GCS1772














































Reviews:

No comments

Related manuals for MiniView GCS1772

MMAC-Plus 9G426-02

Brand: Cabletron Systems Pages: 12

MMAC-Plus 9F310-02

Brand: Cabletron Systems Pages: 4

Brand: Cabletron Systems Pages: 16

Brand: cable matters Pages: 4

Brand: CableCreation Pages: 7

Brand: OEZ Pages: 5

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 1

Cleveland Controls RSS-498-013

Brand: UNICONTROL Electronic Pages: 2

Brand: Gembird Pages: 2

Brand: FS Pages: 43

Brand: I-Tech Pages: 19

Brand: Linkskey Pages: 2

Brand: AMAV Pages: 8

Brand: Kramer Pages: 2

8265 Nways ATM Switch

Brand: IBM Pages: 100

Brand: Goobay Pages: 16

Brand: Top View Pages: 13

Brand: Parallax Power Supply Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands