background image

ii

IMPORTANT NOTE

: The audio may activate in the middle of a call due to

factors like excessive wiring (see page 12 item 8), bad or old wiring , existing
unstable lines, sparks, too many wall jacks , Noisy phone lines, Bad
telephones, “Hot Lines” (see P6 special cases)

If that ever happens, press the 

FLASH

 button to stop the audio!  and

continue your conversation.  The  

FLASH

 button is found on every telephone,

it could be labeled as 

CALL WAIT / FLASH 

or

  LINK 

or

 ON 

or

 TALK 

button

Connection Test: 

To confirm that you have connected everything correctly:

Set Mode switch to SD,  Turn Speaker ON, make sure you can hear the audio from the SX8800, adjust the
volume up (clockwise) if needed, set two ABC switches in front to C position and the two 123 switches in the back
to 3 position,
select line 1 on the phone, L1 LED on SX8800 must turn ON and you should hear audio from the phone Line 1
select line 2 on the phone, L2 LED on SX8800 must turn ON and you should hear audio from the phone Line 2
select line 3 on the phone, L3 LED on SX8800 must turn ON and you should hear audio from the phone Line 3
select line 4 on the phone, L4 LED on SX8800 must turn ON and you should hear audio from the phone Line 4

Double check  your connections or adjust the volume if needed.
This completes the test you should change the ABC and 123 switches now to proper setting as follows:

Switch setting:  

 Please Read the Operation instructions for each setting carefully

There are two pair of  3 position switches on the SX8800 that control the activation method,  you need to select
the proper setting based on your type of phones:

A1, A2, A3: Hold button activation

Use one of these settings when all phones are corded & are same model (for example all are ATT 992) and are
compatible with Hold button activation (see the list in page 3)

B1, B2: 

These two settings utilize 

Flash then Hold

 activation method, this setting

            supports any  phone and any mix of brands with instant activation
            by pressing Flash then Hold

• 

Use B1 or B2 settings if  your phones are Cordless type (including corded base s portables)

• 

If you  have mixed cordless type phones with corded type phones

• 

If you  have  corded type phones that are not all the same model for example ATT brand and
Panasonic brand are both used in your office

• 

If you have any phone that does not activate by pressing Hold  (for example ATT 1040)

B3: Hold button activation 

or 

Flash

 See page P4 for full details.

C1, C2:

 

Voice Activation Mode

 These two settings utilize 

Delayed Hold activation

 method, most phones

cordless or corded or mixed can be activated for music on hold in less than 15 seconds after you press HOLD.

C3: Test mode

Note: Do not set the volume too loud it may flicker or shut off the on-hold audio.

Note: Do not use a Cell phone near the device  to setup or test the device. Use a fax line, etc.

P2

Summary of Contents for SX8800-2LPE












Reviews: