manualshive.com logo in svg

Invitrogen PowerEase 500, Instructions For Use Manual

Share
Download
Invitrogen PowerEase 500 Instructions For Use Manual Download Page 20

Using PowerEase

®

 500 

  

Introduction 

You can operate the PowerEase

®

 500 Power Supply immediately after 

installation using three simple steps (see below). For programming custom 
settings, see page 13. 

 

Starting 
PowerEase

®

 500  

1.  Plug the power cord of the PowerEase

®

 500 Power Supply into an available 

electrical outlet rated at the appropriate electrical values for the power 
supply. 

2.  Turn on the main power switch located on the rear of the PowerEase

®

 500 

Power Supply (see page ix for rear view of PowerEase

®

 500 Power Supply). 

Always leave this switch in the 

ON

 position to keep the back-up battery fully 

charged. 

3. Press 

the 

Power

 button located on the keypad (see page x for a figure of the 

keypad). This 

Power 

button is a secondary power button and does not 

actually shut the instrument down, but shuts down the high voltage, fan, 
and LCD screen. When powered back up, the LCD screen will revert to the 
same screen as when the secondary power was shut off. 

4. A 

Start-Up

 screen will appear (see next page).  

To avoid condensation, the main power switch located on the rear of the unit 
should be left on between use during operation in a cold room or in high 
humidity environments. 

 

Operating 
PowerEase

®

 500  

A simple operating procedure of the PowerEase

®

 500 Power Supply is provided 

below. For more details on the different screens and custom methods, see pages 
5-13. 

1.  Turn on the PowerEase

®

 500 Power Supply. 

2. Press 

Select

 once the 

Start-Up

 screen appears. 

3.  Select your gel type from the 

Gel Method

 screen. 

4.  Choose the number of gels to be electrophoresed from the 

Gel Quantity

 

screen. 

5. Press 

the 

Start

 button to begin electrophoresis. 

Note

: To reset the PowerEase

®

 500 Power Supply, press the 

Stop

 button. 

  

 

The maximum number of Novex

®

 mini-gels that can be electrophoresed at the 

same time using PowerEase

®

 500 Power Supply and the XCell 

SureLock

™

 Mini-

Cell is listed below: 

Gel Type 

Number of Gels 

Novex

®

 Tris-Glycine Gels 

10 gels 

NuPAGE

®

 Novex Tris-Acetate Gel 

6 gels 

NuPAGE

®

 Novex Bis-Tris Gels 

2 gels 

Novex

®

 Tricine Gels 

4 gels 

Novex

®

 TBE-Urea gels 

10 gels 

Continued on next page 

  

5 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for PowerEase 500






































Reviews:

No comments

Brands by name

Popular brands

Load more brands