InVid PAR-P2TEMPTABLET User Manual Download Page 38 | Manualshive

Page: 38 / 64

background image

33

Temperature Screening & Face Recognition Terminal User Manual

3. Set alarm trigger options. Trigger alarm out, Email and FTP. The setup steps are the same
as temperature screening settings. Please refer to temperature screening settings chapter for
details.

6.3.4 IP Address Conflict

1. Go to Config



Alarm



Anomaly



IP Address Collision as shown below.

2. Click “Enable alarm” and set the alarm holding time.
3. Trigger alarm out. When the IP address of the camera is in conflict with the IP address of
other devices, the system will trigger the alarm out.

6.3.5 Cable Disconnection

1. Go to Config



Alarm



Anomaly



Cable Disconnected as shown below.

2. Click “Enable” and set the alarm holding time.
3. Trigger alarm out. When the camera is disconnected, the system will trigger the alarm out.

6.3.6 Alarm In

To set sensor alarm (alarm in):
Go to Config



Alarm



Alarm In interface as shown below.

«
...
36
37
38
39
40
...
»

Summary of Contents for PAR-P2TEMPTABLET

































































Reviews:

No comments

Related manuals for PAR-P2TEMPTABLET

Brand: Datavan Pages: 44

Brand: Symbol Pages: 39

Brand: EBN Technology Pages: 19

Brand: Pilz Pages: 43

Brand: Elo TouchSystems Pages: 33

Brand: FingerTec Pages: 5

Brand: FingerTec Pages: 32

Brand: PAX Pages: 65

Brand: 3M Pages: 14

Brand: POSIFLEX Pages: 10

Worldline YOMANI TOUCH XR AUTONOM

Brand: SIX Payment Services Pages: 22

Brand: NCR Pages: 128

Brand: Datecs Pages: 23

Brand: EBN Technology Pages: 15

PanelView Plus 6 1000

Brand: Allen-Bradley Pages: 168

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands