background image

En

9

Main menu

Sub-menu

Description

Inputs

Status

Displays the status of the input signals for ASI1, ASI2, TUNER and IP IN 

DVB-S2

This menu is only displayed on IDLV-5100P-xxS2 models

LNB Frequency:

 Input LNB frequency

Satellite Frequency:

 Input downstream frequency of satellite

Symbol Rate:

 Input symbol rate of satellite

LNB Voltage:

 Select the correct LNB voltage output of the F-connector: Off, 13 

V, 18 V. <13V for Vertical/Left hand polarization, 18V for Horizontal/Right hand, 
OFF for LNB Power off.> 

LNB 22KHz:

 Activate the LNB 22 kHz control signal to the LNB: On or Off. 

<22KHz control signal switches the LNB to receive high band if any> 

DISQEC:

 Select OFF/Port A/Port B/Port C/Port D

PLS Gold Code:

 N/A

Frequency Offset High:

 Set the frequency offset for signal lock. the range is 

1000~5000KHz

Frequency Offset Low:

 The range is -5000KHz~-1000KHz

COFDM

This menu is only displayed on IDLV-5100P-xxT models

Frequency:

 Enter the frequency of the COFDM signal in MHz.

DVB-T2

This menu is only displayed on IDLV-5100P-xxT2 models

Frequency:

 Input terrestrial frequency.

Bandwidth:

 Select bandwidth - 6Mhz, 7Mhz or 8Mhz.

QAM

This menu is only displayed on IDLV-5100P-xxC model

Constellation:

 Enter the modulation mode of the QAM signal.

Frequency:

 Enter the frequency of the QAM signal in MHz.

Symbol Rate:

 Edit the symbol rate to the proper value in KBaud.

RSSI

Display the quality of the received DVB-S2 signal.

Ethernet

This menu is only displayed on IDLV-5100P-20x and -44x models which set TS/

IP streaming board as “100M Single IN”

Stream IP Addr:

 Enter the IP address for streaming IP input of the unit. 

Stream Netmask:

 Enter the network sub mask for the subnet to which the unit 

is connected for IP streaming traffic.

Stream Gateway:

 Set the gateway for the network to which the unit is con-

nected for IP streaming traffic.

Stream Mac Address: 

Ffactory-set MAC addresses are guaranteed to be 

unique. Therefore you cannot configure the address.

Multicast IP Addr:

 Enter the IP address of the multicast stream for the trans-

port stream over IP.

Multicase UDP Port:

 Enter the UDP port number of the TS over IP stream.

Protocol: 

Select the protocol for multicast: UDP or RTP.

Output Smoothing:

 Set the quality of TS that is received via the TS/IP input. 

Auto:

 The bit rate is variable.

Disable: 

The unit let the TS pass by.

Fixed Rate:

 The bit rate is fixed.

TS Bit Rate:

 Set the bit rate of the TS received via the TS/IP input. The setting 

is only valid when the output smoothing is configured as Fixed Rate.

Summary of Contents for IDLV-5100P













































Reviews: